Stimmen - 5, Durchschnittliche Bewertung: 4.6 ( )

Hersteller: Peavey Dateigröße: 138.45 kb Dateiname: 6ddae34f-c99c-4ddd-80e6-4aaa2fa9a53b.pdf Unterrichtssprache:

13 Loading MIDI Files containing a Vocoder track 13 aaaaaaaaaaaaaaaaaaaaa0 Vocal Processor About the Vocal Processor Installing the Vocal Processor kit activates Equinox’s Mic/ Line interface, allowing you to sing and play instruments through the instrument’s pre-amp, process the mic or line signals with the internal Digital Effects Processors and direct the processed signals to the stereo and mono outputs. In addition, the Vocal Processor feature allows you to add vocal harmonies to your live singing, so that you can play and record songs with your own harmonized vocal backings. You can easily upgrade your Equinox with the Mic/Line and Vocal Processor features by installing the optional Vocal Processor card and loading the new Operating System software from disk. The new features offered by the Vocal Processor 1. Vocal harmonies can be added to your voice according to various preset configurations. 2. The signals input at the Mic/Line 1 and 2 jacks can be independently processed by Equinox’s internal Digital IMPORTANT: The new Op- Effects Processors and directed to the outputs. erating System updates the instrument’s Flash Rom with 3. A microphone Equalizer is available to process the mi- the new Vocal Processor crophone signal at the Mic/Line 1 input. function, but it is indispensa ble that you install the Vocal 4. New functions assignable to the Pedals are available Processor card into your to control the Mic/Line and Vocal Processor. New MIDI Equinox to render the Vocal Processor operative. Controllers have also been implemented to control the additional features via MIDI. 0 0 0 aaaaaaaaaaaaaaaaaaaaaaaaaa0 Introduction 1 Loading the Operating System The new Operating System upgrade rewrites the instrument’s Flash ROM memory, therefore, before updating the instrument, be sure to save all user-programmed data (Songs, Performances, Grooves, Drawbars, etc.) to disk or hard disk. If your instrument is installed with a SCSI interface, you can save any user programmed data to an external SCSI device. STEP 1 With the instrument turned OFF, insert the Generalmusic Operating System disk into the disk drive. After you have inserted the disk, turn the instrument ON. STEP 2 You will see a message in the instrument display screen that says: Loading OS-DISK clears ALL MEMORY!! Press ENTER and wait about 3 minutes for the new Operating System to load. When the new system has finished loading, you will see the following message in the instrument display screen: Loading Successful!! At this time, Press ENTER again and the instrument will proceed through the normal operating display screens. You can now Turn OFF the instrument in preparation for the final step explained below. IMPORTANT: REMOVE THE OPERATING SYSTEM DISK BEFORE PROCEEDING TO THE FINAL STEP! FINAL STEP As you turn the instrument ON, KEEP ROTATING THE DIAL until the following message appears in your display screen: !!WARNING!! Dial on Power-Up Requests Memory Clear!! Press ENTER. You have now completed the update process, and your Equinox has been permanently upgraded. 0 0 aaaaaaaaaaa0 2 Vocal Processor a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a Introduction 3 Connections To work with the Vocal Processor, the minimum amount of equipment you will need is: 1. A low impedance microphone with a standard jack connector on the other end of the cable. 2. An amplification system (domestic hi-fi unit, amplified speakers, mixer, etc.). 3. Although not essential, you can also use one or both types of optional control pedals to control the Mic/Line and Vocal Processor features: a switch-action pedal and a Continous control pedal. Microphone: to add vocal harmonies to our voice, connect the Microphone to the MIC/LINE 1 jack. Note: The Mic/Line 2 jack can also accept a microphone, but this jack is not enabled for the Vocal Processor features. You can sing (or play an instrument) through the Mic/Line 2 input, process the signals with Equinox’s internal Digital Effects Processors and direct the processed signals to the outputs. Switch and/or Continuous Pedals: plug the pedals into the PEDAL 1 or 2 or DAMPER jacks, program the jacks appropriately for a Continuous or Switch action pedal and assign the new Vocal Processor functions to the pedal(s) accordingly (Vocal Volume, Vocal On/Off). Activate the Mic interface and the Vocal Processor After loading the new operating system and connecting your microphone to the Mic/Line 1 jack, the first thing to do is to activate the Mic/Line interface and the Vocal Processor. Press the SYSTEM button then go into the MASTER menu, (F3). Now press the MIC/LINE button, (F2) to open the MIC/LINE INPUTS screen. Here, you can enable both the Mic/Line interface (Mic/Line = ON) and the Vocal Processor (Vocal Proc. = ON): Mic/Line = On Vocal Processor = On With the Mic/Line interface On, you can sing or play through the instrument’s pre-amp, proces...

Herunterladen

Geben Sie zwei Ziffern: