Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
B. The mixer has been exposed to rain or water. C. The mixer does not appear to operate normally or exhibits a marked change in performance. Q-D3™ Main Features • VCA Fader for Q-Start Control • Adjustable Crossfader Curve - for crabbing • Selectable Voltage 115v~230v • 2 Phono/2 Aux, 2 Line Inputs • Fader “Q” Start on both channels • Q-Start Compatible (for use with compatible American Audio CD Players ) • -30dB Rotary Kills for Treble, Bass and Mids on both channels • Separate gain control for each channel • High output to headphones • Replacable/Adjustable Transformer Switches ©American Audio® -• Soft-touch rubber knobs for better control • Extremely clean signal to noise ratio • Light Control Signal Output Jack • Talk Over Button - Reduces channel output gain by 15dB +/- 2 dB • Dual Function Stereo LED Level Indicator Indicated Master and PFL (Pre Fader Level) Signal Levels • Split Cue Monitoring • Cue Mixing • 100% Push Button Kills • Push Button Kills - Q-D3™ Instruction Manual Page 3 American DJ would like to thank for your purchase of this great product. For those of you that are to impatient to read the entire user manual we have compiled these quick start instructions. We hope that you will at least read through these instructions to familiarize yourself with the basic understanding of the unit. The Q-D3 is part of American DJ’s continuing evolution in audio technology. This unit has been built and designed with the typical DJ in mind, by DJ’s. We have attempted to provide you with the most reliable product on the market by using only components made from quality products. MASTER LEVEL - Use this level control to set your volume output. Try never to send an output of more than +4dB to your system. Signal at levels higher than this will start to distort and may cause damage to your system and speakers. Remember that a distorted signal from you mixer will only be multiplied throughout your system. CHANNEL TRIM LEVEL - The channel trim levels are not to be used as volume controls, never use the channel trim to set the output volume. These controls are used to aid in distortion control. Use these control to preset your signal level before the crossfader. With your channel faders in the maximum position, use the channel trim level to set an average output level of about +4dB on you master level meter. HEADPHONES - To avoid sever hearing damage, always be sure the headphone level is set to minimum before plugging them in. Never put the headphone on without making sure the headphone level is turned down. MAIN MIC - The main mic connector uses a 1/4” jack unbalanced connector. The DJ mic has an independent volume control. When feedback occurs when using the mic, try lowering the “low” level this may reduce the feedback. Always leave the mic level to it’s minimum level when not in use. PHONO/AUX SWITCH (29) - This switch is used to change the selected input from phono level to line level and vice versa. Channels 1 and 2 may be switched PHONO/AUX or LINE. The selectors for AUX1/PHONO1 and AUX2/PHONO2 are on the rear panel (24). Q-START FEATURE - This function works in conjunction with a compatible American DJ “Q”Start CD player. When used with a compatible CD player, you can use the crossfader to start and stop the CD Player with the slide of the fader. The ON/OFF “Q ”START switch activates this FADER “Q ”START feature. Q-D3™ QUICK START INSTRUCTIONS ©American Audio® - - Q-D3™ Instruction Manual Page 4 8 9 10 11 12 7 6 5 4 3 2 1 16 19 18 17 15 14 13 Q-D3™ Controls and Features 1. FEATHER FADER PLUS CROSSFADER - This fader is used to blend the output signals of channels one and two together. When the fader is in the full left position (channel 1), the output signal of channel one will be controlled by the master volume level. The same fundamentals will apply for channel two. Sliding the fader from one position to another will vary the output signals of channels one and two respectively. When the crossfader is set in the center position, the output signals of both the channels one and channels two will be even. 2. HAMSTER SWITCH - This switch changes the polarity of the Crossfader (for crabbing). Channel 1 will be activated by the right side of the crossfader (mixing from right to left), and Channel 2 will be activated by the left side of the crossfader (mixing from left to right). 3. CHANNEL FADER - These faders are used to control the output signal of any source assigned to its particular channel. ©American Audio® - - Q-D3™ Instruction Manual Page 5 Top Panel Q-D3™ Controls and Features Cont. 4. CHANNEL TRANSFORMER SWITCH (REPLACEABLE AND ADJUSTABLE) -These switches are used to select the input source assigned to each channel. Each channel may only be assigned one input source at a time. The TRANSFORMER SWITCH may be used in an up/down or left/right pattern. To adjust the transformer orientation please follow the instructions on page 12. 5. PFL BUTTON...