Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
To avoid this problem: • Leave the finish room undisturbed for 24 hours prior to applying the finish. • Avoid making unnecessary movements upon entering the finish room. • Apply the finish to the guitar parts and immediately leave the finish room. • DO NOT return to the room until the specified drying time has elapsed. Note: Depending upon the type of finish used and environmental factors, drying time will vary. Sometimes it may take up to a month for the finish to reach its full hardness. -8- Model H7582 Junior Electric Guitar Kit Tuners Components Needed Qty Guitar Neck.......................................................1 Bushings............................................................6 Tuning Head Plate.............................................1 Black Screws #3 x %".......................................7 Wooden Block...................................................1 Hammer.............................................................1 Peghead Reamer or a Round File (Optional) ... 1 The tuning head plate consists of six machine heads on a metal plate. The machine heads are attached to the headstock with bushings and small screws. To install the tuners: 1. Place the six bushings into the holes on the face of the headstock (Figure 6). The holes may need to be widened with a peghead reamer or a round file. DO NOT widen the holes too much—the bushings should fit snugly. Figure 6. Installing plastic bushings on head-stock. 2. Place a wooden block on the bushings and lightly tap the block with a hammer (Figure 7) until the bushings are seated against the face of the headstock. Figure 7. Seating bushings. 3. Slide the machine heads through the bushings from the back face of the headstock. 4. Align the tuning head plate over the mounting holes and secure with #3 x %" black screws as shown in Figure 8. Figure 8. Tuning head plate installed correctly. Model H7582 Junior Electric Guitar Kit -9- Neck Components Needed Qty Guitar Neck.......................................................1 Guitar Body.......................................................1 Neckplate...........................................................1 Silver Screws #7 x 13/4".....................................4 The neck is pre-finished and is ready to install. To attach the neck to the guitar body: 1. Place the neck into the neck pocket (Figure 9). If the neck does not fit into the pocket, lightly sand the high points on the neck until it fits. 2. Place the neckplate over the neck pocket holes and thread four #7 x 13/4'' silver screws (Figure 10) through the guitar into the neck. DO NOT use glue, since you may want to remove the neck for maintenance and tune-ups. Figure 10. Neckplate installation. Figure 9. Neck installation. -10- Model H7582 Junior Electric Guitar Kit Electronics Components Needed Qty Guitar.................................................................1 Black Screws #3 x 3/4".......................................2 Black Screws #2 x W.......................................6 Silver Screws #3 x V2".......................................2 Circuit Board......................................................1 Pickup................................................................1 Speaker.............................................................1 Battery Case......................................................1 Jack Plate..........................................................1 After the pickup, battery case, and speaker are installed, solder them onto the jacks and the circuit board. Pickup The pickup is installed onto the front of the guitar. To install the pickup: 1. Place the guitar face-side up. 2. Insert the pickup wire (Figure 11) through the hole in the pickup mortise and into the circuit board mortise. Figure 11. Pickup installation location. 3. Insert the pickup into the mortise, positioning both of the #3 x 3/4" black screws through a spring. 4. Secure the pickup to the guitar body with the black screws. Be careful NOT to thread the screws through the pickup wire. 5. Turn the guitar over so the back is face-side up. 6. Solder the pickup wire onto the volume control as shown on the Wiring Diagram on Page 23 and the Electrical Components photos on Page 24. Speaker To install the speaker: 1. Place the speaker mesh cover in the bottom of the speaker mortise 2. Align holes on the speaker with holes in the mortise and fasten the four #2 x W black screws. 3. Insert the two black wires on the headphone jack through holes in the circuit board mortise and battery case (Figure 12) and into the speaker mortise. Figure 12. Speaker wires in battery case mortise. 4. Solder the speaker wires onto the speaker as shown on the Wiring Diagram on Page 23 and the Electrical Components photos on Page 24. Model H7582 Junior Electric Guitar Kit -11- Battery Case To install the battery case: 1. Insert the battery case wires through the left hole in th...