Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
By reversing direction Channel 2 will be on the left and Channel 1 will be on the right. 10. Transform Buttons are for quickly reversing the crossfader direction in order to create various special effects. Numark - The Proven Leader in DJ Technology ©1998 Numark Industries 6 DM1001X/DM1002X CUE SECTION 11. Cue Assign Toggle is used to route pre-fader channel audio to the Cue Monitor Section. 12. The Program Mix controls the mix of Cue and Program audio in the headphones so that beats can be matched exactly and segues are smooth when a song is cued. 13. The Headphone Volume control sets the level for you headphones. 14. The Headphone Jack is used to connect headphones with a standard 1/4" stereo plug. 15. The Stereo Master Fader controls the overall output level. 16. Stereo Output Level Indicator. This fast, accurate stereo meter tracks the output level. It's OK to be occasionally "in the red" as long as +5dB or +8dB aren't constantly lit. Set the crossover, equalizer and power amp inputs to avoid distortion at each step in the audio chain. Proper attention to the meter results in the punchiest possible sound without audible distortion. 17. Power Switch and Power-On LED. DM1001X/DM1002X FRONT PANEL DIAGRAM... 1 2 3 CURVE SWITCH POSITION 1. Microphone Jack for a 1/4” Microphone connector. SWITCH RIGHT Fader mid-point Right Track Left Track 2. Crossfader Curve Adjust Switch Postition-Right: The crossfader creates a short cut to bring in the opposing track to full volume prior to the mid point in the fader. SWITCH LEFT Position-Left: The crossfader creates a standard cut to bring in the opposing Fader track to full volume at the mid point in the fader. mid-point Left Right Track Track 3. Headphone Jack for connecting headphones with a standard 1/4" stereo plug. Numark - The Proven Leader in DJ Technology ©1998 Numark Industries 7 DM1001X/DM1002X DM1001X/DM1002X REAR PANEL DIAGRAM... REAR PANEL: INPUTS AND OUTPUTS 1. Power Connection. Plug your power adapter in here. See safety precautions on page 3 for proper treatment of the power cord. 2. GND is the grounding lug for all turntables. Always use this connection (your turntable cable should have a grounding wire). 3. The Stereo Main Outputs are low-impedance RCA connectors controlled by the Master fader. 4. The Record Outputs are designed to be hooked up to your tape deck’s input jacks. 5. The Phono Inputs use unbalanced RCA jacks. Your input signal is fed directly to your mixer’s high- quality RIAA phono pre-amplifiers so use this position only for moving magnet cartridges. Line level sources will overload the sensitive phono pre-amps and will sound very bad, so always be sure to toggle the line/phono switch over to line before connection of line sources. 6. The Phono/Line Inputs are unbalanced RCA jacks. The Line Input is selected with the Line/Phono Input switch above it. You can connect stereo audio from HiFi VCRs, cassette and reel-to-reel tape decks, DAT machines, CD players, laser discs, tuners, even synthesizers or other mixing consoles. NOTE: Plug mono audio sources into both Left and Right inputs using a “Y” cable connector. Warning: make sure the LINE/PHONO input switch is set to line before playing any line input level devices through your mixer 8. Line/Phono Input switch. Use this to allow line level equipment to be plugged into your phono inputs. Numark - The Proven Leader in DJ Technology ©1998 Numark Industries 8 DM1001X/DM1002X CONNECTION DIAGRAM... CD PlayerTurntable 2Tape Deck Power Adapter Sound System w/ Amplifier Main Turntable 1 Tape Deck Numark - The Proven Leader in DJ Technology ©1998 Numark Industries 9 DM1001X/DM1002X SPECIFICATIONS... Inputs: Line: 10Kohm input impedance 1V rms sensitivity (for 1.22V output) Mic: 10 Kohm input impedance unbalanced 2V rms sensitivity (for 1.22V output) 60mV rms max input Phono: 47Kohm input impedance 1V rms sensitivity @ 1KHz (for 1.22V output) Outputs: Line: 7V rms max Headphone: .5 watt into 47ohm Distortion: less than 0.01% Signal to Noise Ratio (vs. maximum output) Line: Better than 89dB Mic: Better than 72dB Phono: Better than 80dB Frequency Response: Mic: 20Hz - 15 KHz +/-0.5dB Line: 20Hz - 20 KHz +/-0.5dB Phono: +/- 1dB except for controlled attenuation of -3dB @ 20Hz to reduce rumble and feedback Channel EQ: Bass: +15/-30 dB @ 40 Hz Middle: +15/-30 dB @ 1.36 kHz Treble: +12/-25 dB @ 20 kHz Talkover Attenuation: -16dB Channel KILL: (DM1002X only) Bass: -66 dB @ 50 Hz Middle: -31 dB @ 1.2 kHz Treble: -66 dB @ 15 kHz Power Consumption: 5 watt typical, 7.8watt with full headphone output Numark - The Proven Leader in DJ Technology ©1998 Numark Industries 10 DM1001X/DM1002X BLOCK DIAGRAM... Numark - The Proven Leader in DJ Technology ©1998 Numark Industries 11 Professional Disc Jockey Products Warranty and Service Information Numark Industries, LLC and Numark Internatio...
Dieses Handbuch ist für folgende Modelle:Musikinstrumente - NUMARK DM1002X (66.29 kb)