Stimmen - 5, Durchschnittliche Bewertung: 4.6
(
)
)
|
Anleitung Zusammenfassung
Positions near the center provide fine changes in playback speed. Positions further from the center detent provide more drastic changes in playback speed. 28. Effect Level Mix fader. This precisely sets the audible level of the sample in the mix. 29. Memory Bank Select Pushbuttons A-D. Four banks are available for storing samples. To record a bank go to Write and then hit the bank button. You can record into any combination of banks by pressing multiple bank buttons. After sampling, you can either select the next bank and record it (remember Write is still on, just select the bank and hit Start/Stop) or you can manually select a playback mode. You can play any combination of the Memory Banks from left to right (that is, Memory Bank B will always play before Memory Bank D - but you can play ABCD; BC; BD: ACD; only C; only D; etc.). 30. The large Start-Stop button controls sample recording and sample playback. The small red Effects Indicator LED glows when the sampler is "on". Here are the functions: • Tap the button when in sampler Write mode to begin sampling (the LED will light). Tapping it again ends the sample and the LED goes out. (unless the sampler has run out of memory and shuts off automatically - Once the Effects Indicator LED goes out, the Write LED goes out and the Single LED turns on. • In single or repeat play without Trigger, tap the button to play the sample and tap it again to stop the playback. Every time you play the sample, the music starts from the beginning of the sample. • In Single or Repeat play with Trigger you are ready to "stab" samples. With the Trigger Out, the sample plays all the way through before you can play it again. With it In, you can stab or stutter a sample. When you shout "Rock it - rock the house!" and sample it, it can be played back as R- R-R-R-R-R-R-Rock -Rock- Rock-Rock it - Rock it Rock it Rock - - Rock it - rock the house! by simply "drumming" with your fingers. 31. The Stutter Pushbutton lets you choose between two playback styles, Trigger and Non- Trigger, when in Single or Repeat modes. • When the Stutter is Out and the sampler is set to Single or Repeat mode, each time you tap the Start-Stop button the sample starts to play. The next tap stops sample playback. The next time play starts, the sample re-starts at the beginning. • When the Stutter is In and the sampler is set to Single or Repeat mode, each time you tap the Start- Stop button the sample re-triggers. ABOUT STUTTERING Expensive studio rack-mount samplers and sampling keyboards can re-trigger or stutter. This means "beginning at the start of the sample each time a key is pressed or a drum pad is struck". Re-triggering creates the stuttering "rap" effect. The DM1685/1885 includes a manual stuttering feature. How fast can you tap? Try using two fingers for increased speed. 32. Monitor Pushbutton. To hear the sample or effect in the headphones, press this button. Program Mix still works and you will be able to hear any other input channels with the Cue buttons activated. Numark - The Proven Leader in DJ Technology ©1997 Numark Industries 11 DM 1885X DM1885X REAR PANEL DIAGRAM... 1 2 34 5 6 7 8 9 10 12 777 7 99 811 1. The Balanced Main Outputs are low-impedance XLR type connectors controlled by the Master fader. 2. The Stereo Main Outputs are low-impedance RCA connectors controlled by the Master fader. 3. The Tape Outputs are low-impedance unbalanced RCA jacks which output the program mix and allow you to connect any recording device. 4. The Stereo Zone Outputs are low-impedance unbalanced RCA jacks controlled by the Zone Level controls. 5. The Send can be attached to an external effects processor such as a sampler. 6. Mic is the mic input for the Mic Channel and Channel 4. 7. Channels 1-5 Line Inputs are unbalanced RCA jacks. The Line Input is selected with the toggle switch on the front panel. You can connect stereo audio from HiFi VCRs, cassette and reel-to-reel tape decks, DAT machines, CD players, laser discs, tuners, even synthesizers or other mixing consoles. NOTE: Plug mono audio sources into both Left and Right inputs using a “Y” cable connector. 8. Line/Phono Input switch. Use this to allow line level equipment to be plugged into your phono inputs giving you a total of 8 line input options. 9. Phono Inputs on Channels 1, 2 and 3 use unbalanced RCA jacks. Your input signal is fed directly to the DM1885X's high-quality RIAA phono preamplifiers so use this position only for moving magnet cartridges. Line level sources will overload the sensitive phono preamps and will sound very bad, so always be sure to toggle the line/phono switch over to line before connection of line sources. 10. AC Cord. See safety precautions on page 3 for proper treatment of the power cord. 11. Voltage Selector. Set this for the appropriate voltage in your area 12. GND is the grounding lug for turntables 1, 2 and 3 (phono inputs on Channels 1, 2 and 3). Always use this connection (your turntable cabl...