BII 24550 (0209) 08B26-S3V-2000-91 1 of 7 TOOLS AND SUPPLIES REQUIRED Flat-tip screwdriver Phillipsscrewdriver Ratchet 8 mm, 10 mm, and 12 mm Sockets Shop towel Diagonal cutters 8 mm and 10 mm Combination wrenches INSTALLATION 4. Remove the screws fastening the audio brackets, then pull the audio unit out toward you. Unplug the vehicle connectors and antenna lead from the rear of the audio unit. Customer Information: The information in this installation instruction is intended for use only by sk

They are field adjustable for vertical or horizontal polarization with matched principal plane beamwidths for optimum performance in either orientation. This design also provides improved front-to-back ratio and sidelobe suppression that reduces interference. All models feature a robust mounting structure for consistent performance regardless of weather conditions. • Field adjustable to allow vertical or horizontal polarity. Eliminates co-channel interference from neighboring radiators. Polarit

Данный аппарат включается автоматически. (Телевизор также включится, если используется VIERA Link “HDAVI Control”. Данная функция работает только в режиме “DVD/CD” или “USB” без загруженного/подсоединенного диска/устройства.) например, 2 Выберите пункт. . Для выхода нажмите [START]. 3 Выполните настройки. OK DVD USB EXT-IN RADIO START SETUP DVD USB START RADIO, EXT-IN OK SETUP START DVD/CD OK ВОЗВРАТ Выбор входа Дом. Кинотеатр OK OK DVD/CD Дом. Кинотеатр OK ВОЗВРАТ Выбор входа Воспроизв. Диска

The RKW Series will fit into most lecterns as a convenient way to house and protect presentation equipment. GENERAL DESCRIPTION The RKW wood racks are shipped completely un-assembled for ease of storage and lower shipping costs. The assembly tool is supplied as part of the hardware package enabling fast assembly and setup. MODEL HEIGHT RACKING HEIGHT DEPTH WIDTH RKW12-18 22.5" 21" (12RU) 18" 20.46" RKW16-18 29.5" 28" (16RU) 18" 20.46" ARCHITECH AND ENGINEER SPECIFICATIONS The wood enclosu

Enclosure shall consist of top, bottom, and sides constructed of 5/8" MDF pre-drilled for field assembly. One pair 11 gauge tapped rack rails shall be included, along with all assembly hardware. Specifications subject to change without notice » Atl35 1601 JACK MCKAY BLVD. / ENNIS, TEXAS 75119 U.S.A. 30l_iniJ TELEPHONE: (800) 876-3333 / FAX (800) 765-3435 AtlasSound.com © 2005 Atlas Sound Printed in U.S.A. 001105 ATS002222 RevA 11/05 SL10-2080 TEN

The following pages will describe as succinctly as possible the assembly of your new CD. Although some operations are self explanatory, we strongly suggest you read this booklet to better understand the importance of the different key adjustments. Your CD is a precision instrument and its performance will be affected by the different adjustments. It is important to set up your CD with the utmost care for an outstanding musical performance and enjoyment! FOR YOUR RECORDS Oracle CD Serial Number:

DANGER! Check for stray voltage before attaching Transmitter. Voltage greater than 240 volts will damage equipment and cause personal injury and death. Follow standard procedures for reducing the voltage. WARNING! Potential for electrical shock exists when handling connecting cables while the Transmitter is in the TRACE, FAULT or TONE modes. Turn the Transmitter off before handling connecting cables. Page 4 Direct Connect Method Make sure the Transmitter is off. Plug the direct connect cable int

To select Special Peak mode, press and hold then press . While in this mode the Peak flag will flash. Note: While tracing cables in any mode, keep the Receiver handle in line with the suspected cable path. See section Initial Receiver Configuration (Page 3) to set the power frequency to 50 Hz or 60 Hz. The Receiver can be tuned to locate 3 different harmonics of the chosen power frequency. H50 Hz or H60 Hz (high harmonic): Best for general locating of passive power. L50 Hz or L60 Hz (low harmoni

2 Installing or Replacing the Batteries ........................................ 2 Initial Receiver Configuration .................................................. 3 Receiver Battery Test ................................................................ 3 Transmitter Battery Test ........................................................... 4 Using External DC Power and 5 Watt Output .......................... 4 Locating a Buried Cable ........................................................... 5

When the voltage magnitude is sufficient to impair the accuracy of the ohms measurement, only voltage will be displayed. If the voltage is AC, a sine wave will be visible on the display. If a high AC voltage is detected, a rapid beeping tone will be heard. Page 6 Press to select Trace mode. Press again to select one or all of the four frequencies. The display will alternate between displaying the selected frequency and the output signal current. It is best to choose the lowest frequency for dire