Stimmen - 3, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Anything3D Corp assumes no responsibility or liability for any errors or inaccuracies that may appear in this book. © 2000"2001 Anything3D Corp. All right reserved. CONTENS 1. Safety instructions .................................................. 2 2. Introduction ............................................................ 6 3. Complete set of equipment .................................... 10 4. Description........................................................... 12 5. Installation ........................................................... 14 6. Operating controls ................................................ 16 7. Preparing for photography ..................................... 21 7.1 Connecting the Turntable .................................. 21 7.2. Starting the Turntable ...................................... 27 8. Operating modes .................................................. 29 9. Rotation speed adjustment mode ........................... 33 10. Manual mode...................................................... 37 11. Slave mode......................................................... 40 12. Optional auto mode ............................................. 43 13. Frequently asked questions ................................. 46 14. Recommendations for use ................................... 48 15. Trouble"shooting ................................................ 53 16. Maintenance ...................................................... 55 17. Specification ...................................................... 57 18. Product warranty................................................. 59 NIKON is a registered trademark of Nikon Corporation. Anything3D and Anything3D logo are registered trademarks of Anything3D Corporation. Photo3D and Photo3D logo are registered trademarks of Anything3D Corporation. MS Windows is a registered trademark of Microsoft Corporation. S1. AFETY INSTRUCTIONS 1. SAFETY INSTRUCTIONS 1. Please, carefully read these instructions. 2. The turntable must be installed on a flat horizontal surface, otherwise it won’t work properly. Figure 1.1 3. Use AC power source indicated in the specification ONLY. Figure 1.2 4. Turn on the equipment only via proper" ly earthed sockets. 5. Never use a damaged power cable. 6. When using an extension piece, make sure that the total current value doesn’t exceed the permissible one. 7. The total current consumed by all devices through the common outlet should not ex" ceed its rated current. 8. Always turn off the turntable if the power cable or socket is damaged, if liquid has got inside the turntable or if the turntable works improperly. Figure 1.3 9. After switching the turntable off DO NOT switch it on again before 2 seconds have elapsed. 10. Always switch off your turntable by using the button on the power panel. 11. Never take the plug out of the socket before the indicators on the control panel go off. 12. Before cleaning the table disconnect it from the power source. 13. Never use volatile flammable liquids to clean the turntable. S1. AFETY INSTRUCTIONS S1. AFETY INSTRUCTIONS 14. DO NOT perform maintenance and repair of the turntable yourself. In case of any trouble contact ANYTHING3D. 15. Make sure that during rotation the turnta" ble spinning surface doesn’t contact with the external objects. 16. See to it that the load on the turntable is as close to the center as possible or else it might cause damage to the turntable. (Fig. 1.4) Correct Incorrect Figure 1.4 17. Never place the photographed objects on the turntable while it is spinning. to contents 7 S1. AFETY INSTRUCTIONS I2. NTRODUCTION 2. INTRODUCTION ANYTHING3D XT"100 AND XT"350 MOTOR" IZED TURNTABLES are intended for automa" tion of 3D photography process. With 3D photography the objects you are taking pic" tures of can be seen on the computer screen and you can get the complete visual informa" tion about all their features! Our turntable lets you get the 3D images series of any object you choose. This widely adaptable kind of 3D images is in great demand. They could be used in Internet"shops, on the model agen" cies sites, at the advertising shows, presen" tations, etc. XT"350 model 39" in diameter is intended for making the photos of people and large objects. XT"350 turntable is capable of bearing the heavy objects with a weight of up to 350 lb. XT"100 model is 20" in diameter and bears the objects with a weight of up to 100 lb. XT"350 and XT"100 turntables have the same indication, controls and functional abil" ities. In addition to the common function abilities ХТ"350 turntable is equipped with a frame number sound indication, as well as with a pull"out handle and wheels to move the turntable around your photo studio. The turntable enables a series consisting of different quantities of images (32, 16 or 8 frames). You may take any number of frames depending on your quality and technical re" quirements. A series of 32 frames produces a I2. NTRODUCTION high"quality 3D photo with a b...
Dieses Handbuch ist für folgende Modelle:Stereoanlage - XT350 (1.24 mb)