Stimmen - 3, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
INTRODUCTION Welcome to the Krell family of audio components. You have joined a select gro.up of discriminating listeners who enjoy the finest in music reproduction. Krell Digital (KDI) is dedicated to the development technologically advanced components for the reproduction of dlgita.lly recorded music. These designs continue the Krell tradition of ~ncompromising perf6rmance through leading-edge technology. This Owner’s Reference is divided into several sections, each designed to perform a different function. A Question and Answer section is also included where answers to commonquestions are provided. Should you have any questions or suggestionsplease feel free to contact your authorized dealer or the KRELL staff for assistance. In the unlikely event that your MD-2 should require service you will be pleased to know that it is backed by a c.omprehensive Customer Satisfaction policy and one of the most advanced service facilities in the industry. For detailed information on the terms and conditions of service please consult y_our wa.rranty registration card or your au~orized KREELDistributor. B. TABLE OF,CONTENTS 2 UNPACKING AND ASSEMBLY 3 DUST COVER INSTALLATION 4 BASIC INSTALLATION AND CONNECTIONS 5 OPERATION OF THE CD TRANSPORT 6 REMOTE CONTROL 6 CARE AND CLEANING 7 QUESTIONS AND ANSWERS 9 SPECIFICATIONS 13 WARRANTYAND SERVICE INFORMATION C. UNPACKING AND ASSEMBLY 1. Open the box and remove the top layer of protective foam. The following items will now be visibIe: 1 Dust Cover encased in a protective sleeve 1 CD Stabilizer 1 AC power cord 1 MD-2 RC Remote Control 3 AAA Batteries for MD-2RC 1 Packet containing the Owners Reference and N warranty card ote: If any of these items are not included [?lease con.tact your authorized dealer immediately forassistance. 2. Removethe layer of foam containing these items andset it aside for later use. Carefully remove the MD-2 transport from its box and remove the protective plastic wrap. Note: Save all packing materials. If you must ship your MD-2in the future repack the unit in its original pa, ckag ing to prevent transit damage. If the unit is returnecl to KRELLfor service please send the cover and the remotecontrol unit. Caution: If your MD-2 has the custom lucite cover do not removeit fiom its protective sleeve at this time! This cover is extremely_ delicate and can be. permanentlyscarred if mishandled. Please follow the instructions provided in this Reference for safe installation. 3. Removethe transport screws from the bottom of the unit. Their locations are marked with stickers on the bottom of the chassis. NOTE:Later pro,duction models have a protective plastichub that secures the transport from the top of the unit during shipping instead ot transport screws. Carefullyremove the-black plastic hub by tu~ing it counterclock 4, Remove the voltage identification sticker from the back of the unit. You are now ready to install the dust cover. 2 CAUTION: FAILURE TO REMOVE TRANSPORT SCREWS BEFORE OPERATION COULD RESULT IN DAMAGE TO THE TRANSPORT. CAUTION: FAILURE TO REMOVE THE PROTECTIVE HUB BEFORE THE UNIT IS PLUGGED INTO THE AC RECEPTACLE OR BEFORE OPERATION COULD RESULT IN,DAMAGE TO THE TRANSPORT. ~ D. DUST COVER INSTALLATION 1. Standard Version Smoked Dust Cover: Removethe dust cover, in its protective sleeve, from the shipping foam. To prevent scratching leave the protective sleeve on the dust cover until the cover mounting iscomplet.e. There are two pairs of screws w.ith wasOer-typereceptacles attached to the back panel of the unit tormounting the dust cover. Center the hinge pins on the dust cover over the two pairs of screws. Carefully slide the hinges into the slots Formed by the washers. Push thecover down evenly on both sides until it is fully seated. Finally, removethe protective sleeve. 2. Custom Version Clear Lucite Dust Cover: Removethe dust cover from the protective foam and itsprotective sleeve. There are two pairs of screws with washer-type hinge receptacles on the back. of the un!t. Removethe four screwg from the unit ancl take off the black hinge receptacles. Carefully place the lucite dust cover such that the circular milled-out portion,is centered over the transport. Align the slots in the cover s hingeblocks with ttie holes in the back of the chassis. Thread the four screws into the chassis through the hinge blocks. Tighten down lightly and adjust the cover so it is ce.ntered on the unit. Once the cover is aligned tighten clownthe supporting screws. NOTE:The clear lucite cover must be lowered manually, as it is very heavy and does not have a dampingmechanism. E. BASIC INSTALLATION AND CONNECTIONS 1. Place the unit on a clean level surface away from excessive heat, moisture or light. Ideally, the-MD-2should be placed on the top of an audio component cabinet or other "open air" rigid platform. 2. The MD-2 may be placed in a cabinet. It will require. 17.0 inches of verticaIclearance between the bottom and top shelves for proper operation of the cove...