Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Total playing time Disc number (including selected track) Track number 5 Press ENTER. The track is programed. The program step number appears, followed by the total playing time. 6 To program additional tracks, repeat steps 3 to 5. Skip step 3 to select tracks from the same disc. 7 Press nN. To Do this Cancel Program Press PLAY MODE repeatedly Play until “PROGRAM” and “SHUFFLE” disappear. Clear a track from Press CLEAR on the remote in the end stop mode. Add a track to Do steps 3 to 5. the program in stop mode Clear the entire Press x once in stop mode or program twice during play. Tuner Tuner Tips •The program you made remains after Program Play finishes. To play the same program again, press CD, then press nN. •“--.--”appears when the total CD program time exceeds 100 minutes, or when you select a CD track whose number is 21 or over. Using the CD display You can check the remaining time of the current track or the entire CD. Press DISPLAY repeatedly. During normal play Playing time of the current track t Remaining time of the current track t Remaining time of current CD (1DISC mode) or “--.--”display (ALL DISCS mode) t Clock display (for eight seconds) t Effect status In stop mode During Program Play mode when there is a program: The last track number of the program and the total playing time t Total number of programed tracks (for eight seconds) t Clock display (for eight seconds) t Effect status Presetting radio stations You can preset up to 20 stations for FM and 10 stations for AM. 1 Press TUNER/BAND repeatedly to select “FM” or “AM”. 2 Press and hold m or M (or TUNING +/– on the remote) until the frequency indication starts to change, then release it. Scanning stops automatically when the system tunes in a station. “TUNED”and “STEREO”(for a stereo program) appear. 3 Press TUNER MEMORY. A preset number appears in the display. The stations are stored from preset number 1. Preset number 4 Press ENTER. “COMPLETE”appears. The station is stored. 5 Repeat steps 1 to 4 to store other stations. To tune in a station with a weak signal Press m or M (or TUNING +/–on the remote) repeatedly in step 2 to tune in the station manually. To set another station to an existing preset number Start over from step 1. After step 3, press . or > repeatedly to select the preset number you want to store the other station. You can preset a new station in the selected preset number. continued CD/Tuner Presetting radio stations (continued) To erase a preset station 1 Press and hold TUNER MEMORY until a preset number appears in the display. 2 Press . or > repeatedly to select the preset number you want to erase. Select “ALL ERASE” when you want to erase all the preset stations. 3 Press ENTER. “COMPLETE” appears. When you erase a preset number, the preset number decreases by one and all preset numbers following the erased one are renumbered. To change the AM tuning interval (except for the European and Middle Eastern models) The AM tuning interval is factory-set to 9 kHz (10 kHz in some areas). To change the AM tuning interval, tune in any AM station first, then turn off the system. While holding down ENTER, turn the system back on. When you change the interval, all the AM preset stations are erased. To reset the interval, repeat the same procedure. Tip The preset stations are retained for half a day even if you unplug the power cord or if a power failure occurs. Listening to the radio —Preset Tuning Preset radio stations in the tuner’s memory first (see “Presetting radio stations” on page 11). 1 Press TUNER/BAND repeatedly to select “FM” or “AM”. 2 Press . or > (or press PRESET +/ – on the remote) repeatedly to tune in the desired preset station. Preset number Frequency* * When only one station is preset, “ONE PRESET” appears in the display. To listen to non-preset radio stations Use manual or automatic tuning in step 2. For manual tuning, press m or M (or TUNING +/– on the remote) repeatedly. For automatic tuning, press and hold m or M (or TUNING +/– on the remote). Tips • When an FM stereo program has static noise, press STEREO/MONO repeatedly until “MONO” appears. There will be no stereo effect, but the reception will improve. • To improve broadcast reception, adjust the supplied antennas. Using the Radio Data System (RDS) (European model only) What is the Radio Data System? Radio Data System (RDS) is a broadcasting service that allows radio stations to send additional information along with the regular program signal. This tuner offers convenient RDS features like station name display and location of stations by program type. RDS is available only on FM stations.* Note RDS may not work properly if the station you tuned in is not transmitting the RDS signal properly or if the signal is weak. * Not all FM stations provide RDS service, nor do they provide the same types of services. If you are not familiar with the RDS system, check with your local radio stations for details on RDS services in your area. Receiving RDS broadcasts S...
Dieses Handbuch ist für folgende Modelle:Stereoanlage - MHC-DX30 (240.89 kb)
Stereoanlage - MHC-RG30 (240.89 kb)
Stereoanlage - MHC-RG40 (240.89 kb)