Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
(“PROTECT” and “PUSH POWER” flash alternately.) Turn off the unit, eliminate the short-circuit problem and turn on the power again. • There is no audio output during timer recording. There is no microphone sound. • Turn VOLUME or MIC LEVEL to adjust the microphone volume. • Make sure the microphone is connected to the MIX MIC jack correctly. There is no guitar sound. • Turn VOLUME or GUITAR LEVEL to adjust the guitar volume. • Make sure the guitar is connected to the GUITAR jack correctly. • Select “MIX GUITAR/KARAOKE” by pressing MIX GUITAR/KARAOKE. There is severe hum or noise. • A TV or VCR is placed too close to the stereo system. Move the stereo system away from the TV or VCR. “0:00” (or “12:00 AM”) flashes in the display. • A power interruption occurred. Set the clock and timer settings again. The timer does not function. • Set the clock correctly. DAILY and REC do not appear when you press the c/CLOCK SET button. • Set the timer correctly. • Set the clock. The remote does not function. • There is an obstacle between the remote and the system. • The remote is not pointing in the direction of the system’s sensor. • The batteries have run down. Replace the batteries. There is acoustic feedback. • Decrease the volume level. • Move the microphone away form the speakers or change the direction of the microphone. The color irregularity on a TV screen persists. • Turn off the TV set once, then turn it on after 15 to 30 minutes. If the color irregularity still persists, place the speakers farther away from the TV set. Speakers “PROTECT” and “PUSH POWER” appear alternately. • A strong signal was input. Press ?/1 to turn off the power, leave the system turned off for a while, then press ?/1 again to turn on the power. • Check the speaker cables in case “PROTECT” and “PUSH POWER” appear alternately again after you turn the system on. Sound comes from one channel or unbalanced left and right volume. • Check the speaker connection and speaker placement. CD Player The CD tray does not close. • The CD is not placed properly. The CD will not play. • The CD is not lying flat in the disc tray. • The CD is dirty (see “Notes on CDs ” on page 25). • The CD is inserted label side down. • The CD is moist. Play does not start from the first track. • The player is in program or shuffle mode. Press PLAY MODE repeatedly until “PROGRAM,” “ALL DISCS SHUFFLE,” or “1 DISC SHUFFLE” disappears. Tape Deck The tape does not record. • The tab has been removed from the cassette (see “To save a tape permanently” on page 25). • The tape has reeled to the end. The tape does not record nor play, or there is a decrease in sound level. • The heads are dirty (see “Cleaning the tape heads” on page 25). • The record/playback heads are magnetized (see “Demagnetizing the tape heads” on page 25). The tape does not erase completely. • The record/playback heads are magnetized (see “Demagnetizing the tape heads” on page 25). There is excessive wow or flutter, or the sound drops out. • The capstans or pinch rollers are dirty (see “Cleaning the tape heads” on page 25). Noise increases or the high frequencies are erased. • The record/playback heads are magnetized (see “Demagnetizing the tape heads” on page 25). Tuner Severe hum or noise (“TUNED” or “STEREO” flashes in the display). • Adjust the antenna. • The signal strength is too weak. Connect the external antenna. A stereo FM program cannot be received in stereo. • Press STEREO/MONO so that “STEREO” disappears. If other troubles not described above occur, reset the system as follows: 1 Press c/CLOCK SET, ENTER/NEXT and ?/1 at the same time. 2 Unplug the power cord. 3 Plug the power cord back in. 4 Press ?/1 to turn on the power. The unit is reset to factory settings. All the settings you made are cleared. Additional Information Specifications AUDIO POWER SPECIFICATIONS: (LBT-XG500 USA models only) POWER OUTPUT AND TOTAL HARMONIC DISTORTION With 6 ohm loads both channels driven, from 120-10,000 Hz; rates 140 watts per channel minimum RMS power, with no more than 10% total harmonic distortion. Amplifier section Canadian model: LBT-XG500 Continuous RMS power output (reference) 160 + 160 watts (6 ohms at 1 kHz, 10% THD) Total harmonic distortion less than 0.07% (6 ohms at 1 kHz, 70 W) European model: LBT-XG700 DIN power output (rated) 200 + 200 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 250 + 250 watts (6 ohms at 1 kHz, 10% THD) Music power output (reference) 430 + 430 watts (6 ohms at 1 kHz, 10% THD) LBT-XG500 DIN power output (rated) 110 + 110 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 140 + 140 watts (6 ohms at 1 kHz, 10% THD) Music power output (reference) 240 + 240 watts (6 ohms at 1 kHz, 10% THD) Other models: LBT-XG80 The following measured at AC 120/220/240V, 50 Hz DIN power output (rated) 240 + 240 watts (4 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 320 + 320 watts (4 ohms at 1 kHz, 10% THD) LBT-XG60 The following measured at AC ...
Dieses Handbuch ist für folgende Modelle:Stereoanlage - LBT-XG500 (256.29 kb)
Stereoanlage - LBT-XG60 (256.29 kb)
Stereoanlage - LBT-XG80 (256.29 kb)