Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
3 Press TUNING +/–. The frequency indication changes and scanning stops when the system tunes in a station. “TUNED” and “STEREO” (for a stereo program) appear. 4 Press TUNER MEMORY. The next available preset number flashes in the display. The stations are stored from preset number 1. 5 Press ENTER/NEXT. The station is stored. 6 Repeat steps 1 through 5 to store other stations. To tune in a station with a weak signal Press TUNING MODE repeatedly until “MANUAL” appears in step 2, then press TUNING +/– to tune in a station. To store another station on an existing preset number Start over from step 1. After step 4, press TUNING +/– to select the preset number on which you want to store the station. You can add a new preset number after the last preset number. To erase a preset number 1 Press and hold TUNER MEMORY until the preset number flashes in the display. 2 Press TUNING +/– to select the preset number you want to erase. Select “ALL ERASE” to erase all preset numbers. 3 Press ENTER/NEXT. When you erase a preset number, all the following preset numbers shift up and reduce by one. To change the AM tuning interval (Except for the European and the Middle Eastern models) The AM tuning interval is factory-preset to 9 kHz (10 kHz in some areas). To change the AM tuning interval to 10 kHz (or 9 kHz), press TUNER/BAND repeatedly until “AM” appears, then turn off the system. While holding down ENTER, turn the system back on. When you change the interval, the AM preset stations will be erased. To reset the interval, repeat the same procedure. Note The preset stations are canceled when you disconnect the power cord or if a power failure occurs for more than half a day. Saving power in standby mode (For LBT-W900AV/ XB800AV only) In standby mode, you can reduce the power consumption to a minimum (Power Saving mode) and thus save energy. 1/u POWER SAVE/DEMO (Power) (STANDBY) DISPLAY /Press POWER SAVE/DEMO (STANDBY) while the system is turned off. The system switches to the Power Saving mode and the clock display disappears. The system is turned on/off by pressing 1/u. To cancel the Power Saving mode Press DISPLAY. The clock display reappears. continued Saving power in standby mode (continued) Tips • Each time you press POWER SAVE/DEMO (STANDBY) in the Power Saving mode, the display switches between the Power Saving mode and the demo mode. • The 1/uindicator and timer indicator (when the timer is set) light up even in the Power Saving mode. • The timer works in the Power Saving mode. Notes • You cannot set the time in the Power Saving mode. • One Touch Play function does not work in the Power Saving mode. 12 Basic Operations Playing a CD — Normal Play You can play up to five CDs in a row. 1/u (Power) VOLUME 1,34 p0/ ) aPJog dialPLAY MODE 2 CD · P AMS =/+ D.SKIP VOL +/– 1 Press PUSH OPEN and place a CD on the disc tray. If the disc is not placed properly, it will not be recognized. With the label side up. When you play a CD single, place it on the inner circle of the tray. 2 Press DISC SKIP (or D.SKIP on the remote) to place up to four more CDs on the tray. The disc tray rotates so you can insert other CDs. 3 Close the front cover. 4 Press one of the DISC 1 - DISC 5 buttons. Playback starts. If you press aP(or CD aon the remote), playback starts from the CD in the playing position. Disc number in the playing position Track number Elapsed time continued Basic Operations Playing a CD (continued) To Do this Stop playback Press p. Pause Press aP(or Pon the remote). Press aPagain to resume playback (or CD aon the remote). Select a track During playback or pause, turn the jog dial clockwise (to go forward) or counterclockwise (to go backward) and release it when you reach the desired track. Or press AMS* +(to go forward) or AMS =(to go backward) on the remote. Find a point Press and hold )or 0during in a track playback, and release at the desired point. Select a CD Press one of the DISC 1 - DISC 5 buttons (or DISC SKIP). Play only the Press PLAY MODE repeatedly CD you have until “1 DISC” appears. selected Play all CDs Press PLAY MODE repeatedly until “ALL DISCS” appears. Remove or Press PUSH OPEN. change the CDs Adjust the Turn VOLUME (or press volume VOL +/– on the remote). * AMS: Automatic Music Sensor Tips • Pressing aPwhile the system power is off automatically turns on the system and starts CD playback if there is a CD on the tray (One Touch Play). One Touch Play is not available in Power Saving mode. • You can switch from another source and begin playing a CD just by pressing aP, one of the DISC 1 - DISC 5 buttons, or CD aon the remote (Automatic Source Selection). • If there is no CD in the player, “NO DISC” appears in the display. • You can change the CD which is in the loading position during playback of the CD which is in the playing position. Recording a CD — CD Synchro Recording This function lets you easily record from a CD to a tape. You can use TYPE I (normal) or TYPE II (CrO2) tapes. The recording level is automat...
Dieses Handbuch ist für folgende Modelle:Stereoanlage - LBT-DR8AV (885.74 kb)
Stereoanlage - LBT-W900AV (885.74 kb)
Stereoanlage - LBT-XB800AV (885.74 kb)