Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
22 Recording CD by specifying the track order ................................................ 23 Sound Adjustment Activating the bass sound ................... 25 Activating the sound effect ................. 25 Other Features Falling asleep to music ........................ 26 Waking up to music ............................. 26 Timer-recording radio programmes.. 28 Additional Information Precautions ............................................ 30 Troubleshooting ................................... 31 Specifications ........................................ 33 Index ....................................................... 35 Getting Started Getting Started Step 1: Hooking up the system Follow steps 1 through 6 to hook up your system using the supplied cords and accessories. The rear cover Right speaker Left speaker 1 Remove the rear cover. 2 Connect the speakers. Push in on the 1 Connect the speaker cords to the SPEAKER R jack and the SPEAKER L jack on the rear panel of the unit. SPEAKER L R tabs and pull up 2 Attach the speaker cables to the on the cover. clump. 3 Attach the speakers. 5 Turn the unit upside down holding Facing the front of the unit, attach the speaker connected to the SPEAKER R the glass door with firm hand and jack onto the right side of the unit and set the speaker cord into a groove of the speaker connected to the the unit. SPEAKER L jack onto the left side of the unit. 3 Set VOLTAGE SELECTOR to the position of your local power line voltage (except for North American model.) 220-240V VOLTAGE SELECTOR 110-120V 4 Reinstall the rear cover. Put the wires through the hole at the bottom of the rear cover. 6 Connect the power cord to a wall outlet. Note on the glass door of CD player The CD player cover of the CMT-ED1 is made of tempered glass. Under normal conditions, this tempered glass is more shock resistant and able to bear more weight than ordinary glass. This glass, however, may shatter if it receives a sharp blow or if it is scratched. To detach the speakers 1 Slide the speakers in the opposite direction of the arrows of the illustration in “Attach the speakers” (see step 2 -3 on this page.) 2 After detaching the speakers, set the speaker cords into the speaker cord groove at the bottom of the speaker. Otherwise, the speaker cord could be damaged. Groove Step 1: Hooking up the system (continued) To remove the AM antenna If noise is heard while listening to an AM station, remove the AM antenna from the rear panel and place the aerial outside the cabinet. 1 Remove the rear cover. (See step 1 on the page 4.) 2 Remove the AM antenna. Hook 3 Attach the rear cover. (See step 4 on the page 5.) You can hang the AM antenna on a wall. If noise is heard while listening to an FM station, remove the FM antenna from the rear panel and place the antenna outside the cabinet. To exchange the speaker net You can remove the speaker net drowing up to your side and exchange with the supplied extra net. Tip See wire dressing for the rear panel prior to install the rear cover. Inserting two AA (R6) batteries into the remote } } ] ] Tip With normal use, the batteries should last for about six months. When the remote no longer operates the system, replace both batteries with new ones. Note If you do not use the remote for a long period of time, remove the batteries to avoid possible damage from battery leakage. Step 2: Setting the time You must set the time before using the timer functions. 1/u (Power) 3,5 1 2,4,6 1 Press TIMER SET. The clock of the display begins flashes. When “DAILY” or “TIMER REC” appears, press /±repeatedly so that it disappears. 2 Press ENTER. The hour indication flashes. 3 Press /±to set the hour. The clock uses the 12 -hour system. 4 Press ENTER. The minute indication flashes. 5 Press /±to set the minutes. 6 Press ENTER. The clock starts working. Tip If you make a mistake, start over from step 1. 1 Press FUNCTION repeatedly to Step 3: Presetting select “FM” or “AM.” radio stations 2 Press FM or AM (or TUNER/BAND on the remote repeatedly). You can preset up to 30 stations, 20 for FM and 10 for AM. 3 Press TUNING/PLAY MODE on 1/u the remote repeatedly until (Power) “AUTO” appears. 4 Press TUNING +/– (or /± on the remote). The frequency indication changes and scanning stops when the system tunes in a station. “TUNED” and “ST” (for a2 stereo program) appears. 1 4,6 TUNED PGM MHz ST 5 Press MEMORY on the remote. The preset channel number flashes. 1/u (Power) 2 TUNED PGM MHz ST 4,6 6 Press TUNING +/– (or /± on the remote) to select the preset number you want. 3 5 7 TUNED PGM MHz ST 7 Press ENTER on the remote. The station is stored. 8 Repeat steps 4 through 7 to store other stations. To tune in a station with a weak signal Press TUNING/PLAY MODE on the remote repeatedly until “MANUAL” appears in step 3, then press TUNING +/– (or /±on the remote) to tune in the station. To change the preset number Start over from step 2. Tip The preset stations are retained for about two days when you dis...