Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
The preset time has passed, then music fades out and the player goes off automatically. To cancel the sleep function Press SLEEP to make “SLEEP” disappear. To change the preset time Do the steps 2 and 3 again. The Timer Timer-recording radio programs You can set timer to record the radio at a certain time. You can also record the sound of the component connected to the LINE IN jack, using the timer. Make sure you have set the clock (see “Setting the clock” on page 20.) STANDBY TIMER/ CLOCK DISPLAY/ ENTER 0/–, )/+ Note You cannot preset recording timer and wake-up timer (page 21) at the same time. Tip When you receive the AM program in step 1, press r/Pto check if the noise is heard. If so, press PLAY MODE/ MONO/ST/ISS on the player to select the position that most decreases the noise. Before you begin, make sure the t(clock) indication is not lit in the display. If it is lit, press STANDBY. 1 Tune in the radio station and insert a cassette for recording. 2 Press DIR MODE on Display the player to select One side direction of the tape. Both sides 3 Press TIMER/CLOCK to display the tindication. Do the following operations by checking the display window. 4 Press 0/– or )/+ until “REC” appears in the display, and press DISPLAY/ENTER. 5 Press 0/– or )/+ until “RADIO” appears in the display, and press DISPLAY/ENTER. When recording the sound of the component connected to the LINE IN jack, press 0/– or )/+ to display “LINE,” and press DISPLAY/ ENTER. The Timer Note To change the recording side of the tape from the reverse side (9) to the front side ((), press STANDBY to make the tindication disappear, and press STANDBY again. Tips • The preset settings remain until you reset them. • When you select both sides recording, the recording will stop after the both sides recording finishes so that accidental recording will not be made. • The display window does not light while the recording timer is on. 6 Set the timer to the hour and the minutes you want to start recording. 1 Press 0/– or )/+ to set the hour and press DISPLAY/ ENTER. 2 Press 0/– or )/+ to set the minutes and press DISPLAY/ ENTER. 7 Set the timer to the hour and the minutes you want to stop recording. (Do as step 6.) 8 Press 0/– or )/+ to set the volume you want, and press DISPLAY/ENTER. 9 Press STANDBY. The power goes off. The tindication and the recording side of the tape (front side (()) appear in the display. At the preset time, the power will go on and the recording will start. Then the power will go off at the preset time, and the player will enter the standby mode. To check/change when the recording will start Press TIMER/CLOCK, then DISPLAY/ENTER. Each time you press DISPLAY/ENTER, a stored setting lights up. Change the setting if you need to when the setting lights up. When you finish checking, press TIMER/CLOCK. To listen to the radio, etc. before a timer-recording starts If you turn on the player, you can use it as usual. Before the preset time, tune in the station you want to record and turn off the power. To stop timer-recording Turn off the power. The Timer The Timer Setting Up Hooking up the system Make sure you turn off the power before making any connections. Note Connect the right speaker for this unit only to the speaker terminals of the left speaker. If you connect any other speaker or equipment, malfunction may occur. Tip PMC-D307 only: This unit comes supplied with 8 round (10 mm diameter) slip stoppers. Attach one under each of the speaker’s four corners to prevent the speaker from moving when subject to slight vibrations, etc. 2 AM loop aeral 2 FM aerial Right speaker 1 Speaker cord To a wall outlet 1 Audio connecting cord 1 Power cord 3 AC power cord Left speaker 1 Hooking up the speakers 1 Connect the power cord of the left speaker to the POWER IN jack of the player. Setting Up 2 Connect the audio connecting cord (supplied) to the SIGNAL OUTPUT jacks of the player and the SIGNAL INPUT jacks of the left speaker. Connect the white plugs to the L (left) jacks and the red plugs to the R (right) jacks. Setting 3 Connect the speaker cord of the right speaker to the SPEAKER OUT terminals of the left speaker. Connect the red wire to the (+) plus terminal, and the black wire to the (–) minus terminal. continued Setting Up Hooking up the system (continued) Notes • Do not connect the FM aerial of this player to the outdoor aerial. • Keep the aerials away as far as possible from the speaker cords and other connecting cords. If you do not, noise may be heard. Tip The sound quality may be changed depending on the polarity of the plug. Change the direction of inserting the plug and check the sound quality. 2 Hooking up the aerials AM loop aerial* (supplied) FM aerial** *Reorient the aerial to improve broadcast reception. **Keep the aerial as horizontal as possible. Setting up the AM loop aerial 3 Connecting the AC power cord Connect the AC power cord to the wall outlet. Setting Up 4 Inserting batteries into the remote Insert two size AA (R6) bat...
Dieses Handbuch ist für folgende Modelle:Stereoanlage - PMC-D305 (465.29 kb)