Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
D SYSTEM CONTROL jack Connect the system connector of subwoofer to the SYSTEM CONTROL jack on the unit. Insert the plug of the SYSTEM CONTROL cord into the jack, then secure the screws of the plug. Unit (Left panel) Subwoofer (Rear panel) Plug SYSTEM CONTROL cord Screws 14GB E FRONT SPEAKER terminals Connect the front speaker left/right to the terminals on the subwoofer. Insert only the stripped portion of the speaker cords into the FRONT SPEAKER terminals. FRONT SPEAKER R L Note Be sure to use only the supplied speakers. F VOLTAGE SELECTOR For models equipped with a voltage selector on the subwoofer, set VOLTAGE SELECTOR to the position of your local power line voltage. Depending on the model, the VOLTAGE SELECTOR may differ. VOLTAGE SELECTOR 120V* 220V 230240V * Saudi Arabian model: 120V – 127V G Power Connect the power cord on the subwoofer to a wall outlet after you have make all connections. The demonstration appears in the display. When you press "/1, the system turns on and the demonstration automatically ends. If the supplied adaptor on the plug does not fit your wall outlet, detach it from the plug (only for models equipped with an adaptor). For Saudi Arabian model, refer to “Note on power cord plug shapes” supplied with this system. Using the iPod Insert the iPod Dock Adapter into the iPod 1 or 2 connector before use. For details on the supplied iPod Dock Adapters, refer to the operating instructions supplied with the iPod Dock Adapter. To remove the iPod Dock Adapter, pull it up with your fingernail or a flat object using the slot inside the adapter. Slot Using the remote Slide and remove the battery compartment lid, and insert the two supplied R6 (size AA) batteries, E side first, matching the polarities shown below. Getting EeEe Notes • If you do not use the remote for a long period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. • With normal use, the batteries should last for about six months. When the remote no longer operates the system, replace both batteries with new ones. • Batteries installed devices shall not be exposed to excessive heat such as sunshine, fire or the like. Attaching the speaker pads Attach the supplied speaker pads at each corner on the bottom of the front speakers to stabilize the speakers and to prevent them from slipping. Continued l 15GB 16GB Positioning the speakers You can place your speakers as shown below. AFront speaker (left) BFront speaker (right) CSubwoofer DUnit Example 1: Place the speakers at an equal distance from your listening position. Example 2: This placement suitable for Djing. Notes • Place the speakers at least 0.3 meter (1 foot) away from the unit. • Be sure to place the subwoofer horizontally. When carrying the unit Do the following procedure to protect the disc mechanism. Use the buttons on the unit for the operation. 1 Press "/1 to turn on the system. 2 Press CD. 3 Press A to open the disc tray and remove the disc. 4 Press A again to close the disc tray. Wait until “No Disc” appears in the display. 5 Hold down CD and then press "/1 until “STANDBY” appears in the display. Then, “MECHA LOCK” appears in the display. 6 Unplug the AC power cord. Note Before carrying the unit, be sure to disconnect the USB device or iPod(s). A B C D A B C D Setting the clock Use buttons on the remote for the operation. 1 Press "/1 to turn on the system. 2 Press TIMER MENU. The hour indication flashes in the display. If “PLAY SET?” flashes in the display, press V or v repeatedly to select “CLOCK SET?”, then press . 3 Press V or v repeatedly to set the hour. 4 Press . The minute indication flashes in the display. 5 Press V or v repeatedly to set the minute. 6 Press . The clock starts functioning. Note The clock settings are canceled when you disconnect the power cord or if a power failure occurs. To display the clock when the system is off Press DISPLAY repeatedly until the clock is displayed. The clock is displayed for a few seconds (except when iPod is connected). When an iPod is connected, the display will change to clock automatically. For details, see page 32. Getting 17GB To Do this Basic Operations Playing a CD/MP3 disc 1 Press CD (or FUNCTION +/– on the remote repeatedly to select “CD”). 2 Press A. 3 Load a disc with the label side facing up on the disc tray. When you play back an 8 cm disc such as a CD single, place it on the inner circle of the tray. 4 Press A to close the disc tray. Do not forcibly push the disc tray to close it as this may cause a malfunction. 5 Press HS on CHANNEL B (or N on the remote) to start playback. 6 Turn VOLUME +/– (or press VOLUME +/– on the remote) to adjust the volume. Other operations To Do this Stop playback Press x. Pause playback Press HS on CHANNEL B (or X on the remote). Press HS (or X on the remote) again to resume playback. Select a track or file Select a folder on an MP3 disc Select a file on an MP3 disc while viewing the folder and file names on the display (TRACK SEARCH) F...