Stimmen - 3, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
.Make sure the iPod is connected securely. Speaker system: Full-range, bass-reflex, 10 cm, cone type CD track whose number is 21 or over, or when you 4 Set the time to start playback. .Move the system away from sources of noise. .Make sure the iPod is playing music. Cleaning the cabinet Rated impedance: 6 ohms select an MP3 file. Press ./.. repeatedly to set the hour, and then .Connect the system to a different wall socket. .Adjust the volume. Clean this system with a soft cloth slightly moistened Dimensions (w/h/d): Approx. 140 . 245 . 215 mm with a mild detergent solution. Do not use any type Mass: Approx. 1.9 kg .. .Install a noise filter (available separately) to the power 5 Repeat steps 3 through 4 to program additional press of abrasive pad, scouring powder, or solvent, such as General tracks or files, up to a total of 25 tracks or files. The minute indication flashes. Use the procedure cord. The sound is distorted. Power requirements: 230 V AC, 50/60 Hz thinner, benzine, or alcohol. .Turn down the volume. Power consumption: 63 watts above to set the minutes. 6 To play your program of tracks or files, press .(or The remote does not function. Dimensions (w/h/d) (excl. speakers): Approx. 215 . 140 . 298 mm .Set the “EQ” setting of the iPod to “Off ” or “Flat.” CD ..on the unit) .. 5 Use the same procedure as in step 4 to set the time Mass (excl. speakers): Approx. 3.9 kg .Remove any obstacles between the remote and the The program remains available until you open the disc remote sensor . on the unit, and position the unit The iPod cannot be charged. to stop playback. Specifications Supplied accessories: Remote Commander (1)/R6 (Size AA) batteries (2)/AM loop antenna (1)/FM/DAB lead antenna (2)/iPod Dock Adapters (1 set) tray. To play the same program again, press . (or 6 Select the sound source. away from fluorescent lights. .Make sure the iPod is connected securely. Design and specifications are subject to change without notice. CD .. on the unit) .. .Point the remote at the system’s sensor. Press ./.. repeatedly until the desired sound .Move the remote closer to the system. Main unit .Standby power consumption: 0.5 W source appears, and then press .. The display Messages .Halogenated flame retardants are not used in the To cancel Program Play Amplifier section shows the timer settings. certain printed wiring boards. DIN power output (rated): Press PLAY MODE . repeatedly until “PGM” CD/MP3 player .Halogenated flame retardants are not used in cabinets. 18 + 18 W (6 ohms at 1 kHz, DIN) 7 Press .... to turn off the system. disappears while the player is stopped. Continuous RMS power output (reference): 25 + 25 W (6 ohms at 1 kHz, The system turns on 15 seconds before the preset time. The sound skips, or the disc will not play. 10% THD) CD Over: You have reached the end of the disc while Music power output (reference): 38 + 38 W (6 ohms at 1 kHz, 10% THD) If the system is on at the preset time, the Play Timer To delete the last track or file of the program .Wipe the disc clean, and replace it. pressing .. during playback or pause. will not play. Inputs Press CLEAR . while the player is stopped. .Move the system to a location away from vibration (for Complete!: The preset operation ended normally. AUDIO IN (stereo mini jack): voltage 250 mV, impedance 47 kilohms example, on top of a stable stand). LOCKED: The disc tray does not open. Contact your Outputs To activate or check the timer again .Move the speakers away from the system, or place them nearest Sony dealer. PHONES (stereo mini jack): accepts headphones of 8 ohms or more on separate stands. At high volume, speaker vibration SPEAKER: accepts impedance of 6 to 16 ohms 1 Press TIMER MENU .. No Disc: There is no disc in the system, or you have Presetting radio stations may cause the sound to skip. CD player section loaded a disc that cannot be played. “TIMER SEL?” flashes in the display. System: Compact disc and digital audio system You can preset your favorite radio stations and tune No Step: All of the programmed tracks or files have been Laser Diode Properties .. Play does not start from the first track. 2 Press Emission Duration: Continuous them in instantly by selecting the corresponding preset erased. .Press PLAY MODE . repeatedly until both “PGM” Laser Output*: Less than 44.6.W number. 3 Press ./.. repeatedly to select “PLAY SEL?,” then No Preset (DAB only): There is no stored preset station. * This output is the value measurement at a distance of 200mm from the and “SHUF” disappear to return to normal play. .. objective lens surface on the Optical Pick-up Block with 7mm aperture. Use buttons on the remote to preset stations. press No Service (DAB only): There is no supported DAB Frequency response: 20 Hz . 20 kHz 1 Tune in the desired station (See “Listening to the Starting playback takes more time than usual. broadcast in your country or region. Signal-to-noise ratio: More than 90 dB radio”). To cancel the timer .The following discs take a longe...