Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
At the beginning and end of tape, nothing will be recorded for six to seven seconds. – The recording level is set automatically, regardless of the position of VOLUME or DBB. – To prevent accidental recording, break out the tab on the left shoulder of the tape side that you want to protect. – If " CHECK TAPE " is displayed, the protection tab has been broken. Put a piece of clear adhesive tape over the opening. Do not cover the Chrome tape detection hole when covering the tab opening. One Touch Recording • For One T ouch Recor ding, as soon as you press RECORD, the current source will be recorded on tape deck 2. 1 Load a blank tape in tape deck 2. 2 Press RECORD to start recording. . REC flag starts flashing. 3 Press STOP . to stop recording. Note: – When you press RECORD at TAPE mode, “ SELECT OTHER SOURCE ” will be displayed. One Touch Recording is not possible at TAPE mode. 6/15/00, 3:34 PM Dubbing tapes (from tape deck 1 to tape deck 2) 1 Press TAPE to select tape deck 2 . 2 Load the prerecorded tape into tape deck 1 and a blank tape into tape deck 2. . Make sure that the tape in tape deck 1 has its full spool to the left. 3 Press DUBBING oncefor normal speed dubbing or twicewithin 2 seconds for high speed dubbing. . " NORMAL " (normal speed) or " FAST " (high speed) will be displayed and then followed by " DUBBING ". . HSD flag appears on the display for high speed dubbing. • Dubbing will start immediately . . REC flag starts flashing. 4 Press STOP . to stop dubbing. Notes: – At the end of side A, flip the tapes to side B and repeat the procedure. – Dubbing of tapes is only possible from tape deck 1 to tape deck 2. – To ensure good dubbing, use tapes of the same length. – During high speed dubbing in Tape mode, the sound is reduced to a low volume. – You can switch to other source while dubbing. 3139 116 18652 RECORDING CD Synchro Start Recording 1 Load a blank tape into tape deck 2 and a disc into the disc tray. 2 Press CD to select CD mode . . You can program the tracks in the order you want them to be recorded (see Programming Tracks). If not, the tracks are recorded according to the selected disc. 3 Press RECORD to start recording. . REC flag starts flashing. • CD will start playback automatically. 4 Press STOP . to stop recording. Recording from other sources (only on tape deck 2) 1 Load a blank tape into tape deck 2. 2 Press CD, TUNER or AUX. • Start playback of the selected source. 3 Press RECORD . to start recording. . REC flag starts flashing. 4 Press STOP . to stop recording. Note: – During recording, it is not possible to listen to another sound source. CLOCK View Clock You can view the clock (if it is set) at standby or any source mode. It will be displayed for about 7 seconds. • Press CLOCK/TIMER briefly. . “ 10:25” (the current time) will be displayed. . “ --:-- ” will be displayed if the clock is not set. Clock Setting The clock is set in 24-hour mode, e.g. “ 00:00“ or “ 23:59“. Before setting the clock, you must be in the View Clock mode. 1 Press CLOCK/TIMER to select clock mode. . “ 00:00” or the current time starts flashing. 2 Set the hour withE. or . . TIMER Timer Setting • The system can switch on to CD, TUNER or TAPE 1 mode automatically at a preset time. It can serve as an alarm to wake you up. After half an hour from the preset time, the system will return to the standby mode if no button is pressed. • Before setting the timer, make sure the clock is set correctly. • The timer will always be switched on once it is set. • The volume of the timer will be at the last setting before the set is switched to standby mode. 1 Press and hold CLOCK/TIMER for more than 2 seconds to select timer mode. . “ ON 00:00” or the last set timer starts flashing. The TIMER flag flashes. . The last selected source is lighted while other available sources are flashing. 2 Press CD, TUNER or TAPE to select the desired source. 3 PressE. or . to set the hour for the timer to start. 4 PressE. or . to set the minute for the timer to start. 5 Press CLOCK/TIMER to store the start time. . The TIMER is now set. . The TIMER flag remains on the display. 19 3139 116 18652 C D TUNER TAPE AUX STA N DBY. ON CD 1 • 2 • 3 BAND TAPE 1 • 2 VIDEO n TIMER CLOCK PROGRAM RDS NEWS! DEMOTUNING s sss STOP•CLEARSEARCH PLAY PAUSE PREV NEXT PRESET ss I SDBB DUBBING NORM•FAST RECORD A. REPLAY DIGITAL SOUND CONTROL OPTIMAL TECHNO DSC DBB ROCK JAZZ MASTER VOLUME 3 Set the minute withE. or . . 4 Press CLOCK/TIMER again to store the setting. . The clock starts running. • To exit without storing the setting, press . . Notes: – During clock setting, if no button is pressed within 90 seconds, the system will exit clock setting mode automatically. – When a power interruption occurs, the clock setting is erased. – To set the time with RDS clock, see "Receiving RDS Radio Station" under TUNER section. 6/15/00, 3:34 PM English Untitled-12 19 English TIMER • To exit without storing the setting, press . . • At the preset time, the TIMER will be acti...