Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
1 Tune to a RDS station (refer to “Tuning to radio stations”). 2 Press CLOCK SET/RDS for more than two seconds. . "SEAR TM" is displayed. . When RDS time is read, "RDS" and RDS time value are displayed and the current time will be stored. Note: – Some RDS radio station may be transmitting a real time clock at a minute interval. The accuracy of the transmitted time depends on the transmitting RDS radio station. 15 Tape Operation / Recording English VOLUME INCREDIBLE SURROUND PROGRAM TUNINGALBUM PRESET SOURCE TIMER SET DBBDSC OPEN/ CLOSE RDS CLOCK SETBAND STANDBY-ON ECO POWER RECORD DISPLAY MCM510 MICR O SY STEM iR / Tape playback 1 Select TAPE source. . The display shows “TAPE TAPETAPETAPETAPETAPE” briefly, and the tape counter 000 is displayed. 2 Press OPEN/CLOSE c to open the tape door. 3 Insert a recorded tape and close the tape door. . Load the tape with the open side downward and the full spool to the left. 4 Press EA to start playback. To stop playback . Press C. To reset the tape counter display . In stop mode, press C once. Rewinding / Fast forwarding 1 Press TUNING S/T (a/a on the remote control). . The tape will stop automatically at the end of rewinding or fast forwarding. . During fast winding, you can monitor the tape message with the tape counter. 2 Press C to stop rewinding or fast forwarding. General information on recording . For recording, use only NORMAL (IEC type I) tapes on which the tabs have not yet been broken.This deck is not suited for recording on METAL (IEC IV) type tapes. . The best recording level is set automatically. Altering the VOLUME, INCREDIBLE SURROUND or DBB will not affect the recording in progress. . At the very beginning and end of the tape, no recording will take place during the 7 seconds when the leader tape passes the recorder heads. . To protect a tape from accidental erasure, have the tape in front of you and break out the left tab. Recording on this side is no longer possible. If, however, you wish to record over this side again, cover the tabs with a piece of adhesive tape. IMPORTANT! Recording is permissible if copyright or other rights of third parties are not infringed upon. 16 Preparation for recording 1 Select TAPE source. 2 Load a recordable tape into tape deck with full spool to the left. 3 Prepare the source to be recorded. CD – load the disc. TUNER – tune to the desired radio station. AUX – connect external equipment. When recording is in progress . REC flashes. . To stop recording, press 9. . It is not possible to listen to another source. . It is not possible to activate the timer function. Synchro start CD recording 1 Select CD source. . Press TUNING S/T (./™ on the remote control) to select the desired track to start recording. . You can programme the tracks in the order you want them to be recorded (refer to “CD/MP3CD Operations - Programming the disc tracks”). 2 Press RECORD to star t recording. . Playing of the CD programme star ts automatically from the beginning of the CD. It is not necessary to start the CD player separately. One touch recording 1 Select CD, TUNER or AUX source. 2 If necessary, star t playback of the selected source. 3 Press RECORD to star t recording. Recording timer To record from the radio, you will need to use a preset radio station and to set a star t (ON) and finish (OFF) time. 1 Select the preset radio station to record from (refer to “Radio Reception - Tuning to preset radio stations”). 2 In standby mode, press TIMER SET 3 for more than two seconds. . The current selected source is displayed. 3 Press SOURCE repeatedly until “REC TUN” source is displayed. 4 Press TIMER SET 3 to confirm the source. . “SET ON TIME” is displayed and the clock digits for the hours flash. 5 Adjust VOLUME on the front pannel to set the hours. 6 Press TIMER SET 3 again. . The clock digits for the minutes flash. 7 Adjust VOLUME on the front pannel to set the minutes. 8 Press TIMER SET 3 to confirm the recording star t time. . “SET OFF TIME” is displayed and the clock digits for the hours flash. 9 Repeat steps 5-7 to set the finish time. 0 Press TIMER SET 3 to confirm the timer settings. . is shown and the recording timer is now set. Note: – The recording timer will not be activated if the system is in tape play mode. English 17 Clock/Timer English VOLUME INCREDIBLE SURROUND PROGRAM TUNINGALBUM PRESET SOURCE TIMER SET DBBDSC RDS CLOCK SETBAND STANDBY-ON ECO POWER RECORD DISPLAY MCM510 MICR O SY STEM iR / Clock setting There are two possible methods for setting the clock: manually or automatically by using RDS. Automatic clock setting Refer to “Setting the RDS clock”. Manual clock setting 1 In standby mode, press and hold CLOCK SET/ RDS. . SET CLOCK is displayed briefly.Then, clock digits for the hours flash. 2 Adjust VOLUME to set the hours. 3 Press CLOCK SET/RDS again. . The clock digits for the minutes flash. 4 Adjust VOLUME to set the minutes. 5 Press CLOCK SET/RDS to confirm the time. Timer setting . The system can be used as an alarm cloc...