Stimmen - 0, Durchschnittliche Bewertung: 0 ( )

Hersteller: Philips Dateigröße: 803.13 kb Dateiname: Unterrichtssprache:

. Do not expose the system, batteries or discs to excessive moisture, rain, sand or heat sources caused by heating equipment or direct sunlight. . The lens may cloud over when the system is suddenly moved from cold to warm surroundings, making it impossible to play a disc. Leave the system in the warm environment until the moisture evaporates. . The mechanical par ts of the set contain self- lubricating bearings and must not be oiled or lubricated. . When the system is switched to Standby mode, it is still consuming some power. To disconnect the system from the power supply completely, remove the AC power plug from the wall socket. English 7 Preparations English FM wire antenna AM loop antenna AC power cord R+– L speaker (right) speaker (left) ABC+ – Rear connections B Antennas Connection Connect the supplied AM loop antenna and FM The type plate is located at the rear of the antenna to the respective terminals. Adjust the system. position of the antenna for optimal reception. For users in the U.K.: please follow the instructions on page 2. AM Antenna A Power Before connecting the AC power cord to the wall outlet, ensure that all other connections have been made. WARNING! – For optimal performance, use only the original power cable. – Never make or change any connections with the power switched on. Fix the claw to the slot Position the antenna as far as possible from a TV, VCR or other radiation source. 8 Preparations FM Antenna . For better FM stereo reception, connect an outdoor FM antenna to the FM ANTENNA terminal. C Speakers Connection Front Speakers Connect the speaker wires to the SPEAKERS terminals, right speaker to "R" and left speaker to "L", coloured (marked) wire to "+" and black (unmarked) wire to "-". 12 . Fully inser t the stripped por tion of the speaker wire into the terminal as shown. Notes: – For optimal sound performance, use the supplied speakers. – Do not connect more than one speaker to any one pair of +/- speaker terminals. – Do not connect speakers with impedance lower than the speakers supplied. Please refer to the SPECIFICATIONS section of this manual. Inserting batteries into the remote control Inser t two batteries type R03 or AAA (not supplied) into the remote control with the correct polarity as indicated by the "+" and "-" symbols inside the battery compar tment. CAUTION! – Remove batteries if they are exhausted or will not be used for a long time. – Do not use old and new or different types of batteries in combination. – Batteries contain chemical substances, so they should be disposed off properly. English 9 Controls (illustrations on page 3) English Controls on the system and remote control 1 STANDBY ON y – to switch the system on or to standby mode. 2 TUNER (BAND) – to select waveband : FM or MW. TAPE (TAPE 1•2) – to select tape mode. 3 ECO POWER – to switch the system on or to Eco Power standby mode. 4 CD 1/ CD 2/ CD 3 (CD 1/2/3) – to select disc tray 1, 2 or 3. 5 DSC (DIGITAL SOUND CONTROL) – to select the desired sound effect : JAZZ, ROCK,TECHNO or OPTIMAL. 6 OPEN/CLOSE – to open or close the disc tray. 7 DISC CHANGE – to change disc(s). 8 DBB (DYNAMIC BASS BOOST) – to select the desired bass boost level. 9 PROGRAM for CD ................. to programme disc tracks. for Tuner ............. to programme preset radio stations. for Clock ............ to select 12- or 24-hour clock mode. for Timer ............. to select CD programme mode as the wake up source. 0 Tape deck 1 operation a .......................... to star t recording. E .......................... to star t playback. a / a ............... to rewind or fast forward. 70........................ to stop playback/recording or to open the tape door. A .......................... to interrupt playback or recording. ! Tape deck 2 operation E .......................... to star t playback. a / a............... to rewind or fast forward. 70........................ to stop playback or to open the tape door. A .......................... to interrupt playback. @ CLOCK•TIMER – to view the clock, set the clock or set the timer. # DIM MODE (DIM) – to select different brightness for the display screen : DIM 1, DIM 2, DIM 3 or DIM OFF. $ n – to connect headphones. % MASTER VOLUME v w (VOL + /-) – to increase or decrease the volume. ^ Mode Selection PLAY•PAUSE EA for CD ................. to star t or interrupt playback. for Plug & Play…(on the system only) to initiate and star t plug & play mode. SEARCH•TUNING a a for CD ................. to search backward/forward. for Tuner ............. to tune to a lower or higher radio frequency. for Clock ............ (on the system only) to set the hour. STOP•CLEAR / DEMO STOP C for CD ................. to stop playback or to clear a programme. for Tuner ............. (on the system only) to stop programming or to erase a selected preset. for Demo ........... (on the system only) to activate / deactivate the demonstration. for Clock ............ (on the system only) to exit clock setting ...

Herunterladen

Geben Sie zwei Ziffern: