Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
To cancel the demonstration mode : Press the EX.BASS/DEMO button. • The demonstration mode will be cancelled and the unit will be in the standby mode. Notes : • When the unit is in the standby mode, the display will disappear. • When the power is on, the EX.BASS/DEMO button can be used to select the extra bass mode. • When the power supply is restored after a power failure or the power cord is unplugged and plugged in again during use, this unit will enter into the demonstration mode. Remote control • When inserting or removing the batteries, push them towards the battery terminals. • Installing the batteries incorrectly may cause the unit to malfunction. Precautions for battery use : • Replace all old batteries with new ones at the same time. Do not mix old and new batteries. • Remove the batteries if the unit will not be used for long periods of time. This will prevent potential damage due to battery leakage. • Do not use rechargeable batteries (nickelcadmuim battery, etc.) Note concerning use : • Replace the batteries if the operating distance is reduced or if the operation becomes erratic. • Periodically clean the transmitter LED on the remote control and the sensor on the main unit with a soft cloth. • Exposing the sensor on the main unit to strong light may interfere with operation. Change the lighting or the direction of the unit. • Keep the remote control away from moisture, excessive heat, shock, and vibrations. 10 EN SETTING THE CLOCK 3 4 5 6 7 8 9 2 POWER TUNING/ TIME (%UP fiDOWN) CLOCK MEMORY /SET ON/ STANDBY TUNING/TIME (fi %) CLOCK MEMORY /SET In this example, the clock is set for the 24 hours (0:00) system. 1 Press the ON/STANDBY button to enter the standby mode. 2 Press the CLOCK button. 3 Within 5 seconds, press the MEMORY/SET button. 4 Press the TUNING/TIME (%UP or fiDOWN) button to select the time display mode. “0:00” :The 24-hours display will appear. (0:00 - 23:59) “AM 0:00” : The 12-hours display will appear. (AM 0:00 - PM 11:59) “AM 12:00” : The 12-hours display will appear. (AM 12:00 - PM 11:59) • Note that this can only be set when the unit is first installed or it has been reset (see page 29 - RESETTING THE MICROCOMPUTER). 5 Press the MEMORY/SET button. 6 Press the TUNING/TIME (%UP or fiDOWN) button to adjust the hour. • Press the TUNING/TIME (%UP or fiDOWN) button once to advance the time by 1 hour. Hold it down to advance continuously. • When the 12-hours display is selected, “AM” will change automatically to “PM” 7 Press the MEMORY/SET button. 8 Press the TUNING/TIME (%UP or fiDOWN) button to adjust the minutes. • Press the TUNING/TIME (%UP or fiDOWN) button once to advance the time by 1 minute. Hold it down to change the time in 5 minutes intervals. • The hour setting will not advance even if minutes advance from “59” to “00”. 9 Press the MEMORY/SET button. • The clock starts operating from “0” second. (Second are not displayed.) And then the clock display will disappear after a few seconds. 11 EN To see the time display : Press the CLOCK button. • The time display will appear for about 5 seconds. Note : • The clock display will flash on and off at the push of the CLOCK button when the AC power supply is restored after a power failure occurs or after the AC power cord is disconnected. If this happens, follow the procedure below to change the clock time. To change the clock time : 1 Press the CLOCK button. 2 Within 5 seconds, press the MEMORY/SET button. 3 Perform steps 6 -9 on page 11 . To change the time display mode : 1 Perform steps 1 -2 in the section “RESETTING THE MICROCOMPUTER”, on page 29. 2 Perform step 1 -9 on page 11. CHANNEL SPACE SETTING The space between radio channels has been set to the one that prevails in the area to which the system is shipped. However, if the current channel space setting does not match the setting in the area where the system is to be used, for instance when you move from area 1 or area 2 shown in the following table or vice versa, proper reception of AM/FM broadcasts cannot be expected. In this case, change the channel space setting in accordance with your area by refering to the following table. Area CHANNEL SPACE freq. 1 USA, Canada and Latin America Countries FM : 100 kHz AM : 10 kHz 2 Other countries FM : 50 kHz AM : 9 kHz 1 Press the ON/STANDBY button to enter Caution : the standby mode. • The operation explained above will erase all data 2 Set the SPAN SELECTOR switch to “50/9” for stored in memory including clock and timer set9 kHz AM interval (50 kHz FM interval), and “100/ tings, and tuner and CD presets. 10” for 10 kHz AM interval (100 kHz FM interval). 3 Whilst pressing down the 7 STOP button and the SOUND MODE button, hold down the ON/STANDBY button for at least 1 second. • “CLEAR AL” will appear. 12 EN SOUND CONTROL Volume (Main unit operation) When the VOLUME CONTROL is turned clockwise, the volume will increase. When it is turned anti-clockwise, the volume will decrease. (Remote control operation) Press the VOLUME up button ...