Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Otherwise, the Clip data may be lost. 62 EN Notes on cassette tape Safety tab (accidental erasure prevention tab) After an important recording has been finished, break the safety tab, to prevent the recorded contents from being erased or recorded on accidentally. For A side For B side To re-record Apply tape only to the position where the tab has been removed. To store cassette tapes Do not store the tapes in a place which is subject to direct sunlight, or near equipment that generates heat. Keep the cassette tapes away from any magnetic field. When there is slack in the tape In such a case, insert a pencil into the reel hole and wind the reel hub to remove the slack. . Do not use an endless tape, as this could damage the mechanism of the unit. Do not use a cassette with more than 90minute recording time, for the tape used with such a cassette is very thin and tends to cause troubles such as entanglement around the pinch roller or cutting of tape. Maintenance Cleaning the heads and peripheral components For maintaining the best condition of the deck and for longer service life, always keep the heads, capstan and pinch roller clean. To clean them, perform the following: (1) Open the cassette holder. (2) Using a cotton swab dipped in alcohol, clean the head, capstan and pinch roller carefully. Cotton swab Capstan Head Pinch roller Tape guides Demagnetizing the head When the recording / playback head is magnetized, the sound quality will deteriorate. In such a case, demagnetize the head using a commercially available demagnetizer (head eraser). . There are precisely aligned parts around the heads, including the tape guides. When cleaning, pay special attention so as not to apply shock to them. Continued on next page \ 63 EN Knowledgesection Important items (continued) Maintenance of the unit When the front panel or case becomes dirty, wipe with a soft, dry cloth. Do not use thinner, benzine, alcohol, etc. for these agents may cause discoloration. In regard to contact cleaner Do not use contact cleaners because it could cause a malfunction. Be specially careful not to use contact cleaners containing oil, for they may deform the plastic component. Memory backup function Stored contents which are cleared immediately when power plug is unplugged from power outlet. -Clock display(Backed up for 3 min.) Stored contents which are cleared in at least a day after power plug is unplugged from power outlet. . Amplifier section -Input selection - Volume control value -AUX input level - Tone control levels - Timer setting contents . Tuner section -Receiving band -Frequency -Preset stations -Auto tuning setting . Cassette deck - Tape transport direction - Tape equalizer - Tape reverse mode . MD recorder -Recording mode -Recording speed WARNING NOTICE: In most cases it is an infringement of copyright to make copies of tapes or discs without the permission of the copyright owners. Anyone wishing to copy commercially available tapes or disc should contact the mechanical copyright protection society limited or the performing rights society limited. US and foreign patents licensed from Dolby Laboratories. 64 EN In case of difficulty What seems to be a malfunction is not always so. Before calling for service, check the following table according to the symptom of your trouble. Operation to reset The microcomputer may fall into malfunction when a cord is unplugged and plugged again while the unit is ON or due to an external cause. In such a case, the microcomputer should be reset as described below: Unplug the power cord from the wall outlet and, while holding the POWER key depressed, plug the power cord again. This initializes the microcomputer. Note that this clears the previously stored memory. Common section Sound is not produced. \ Increase the volume level. (page 10) \ Unplug the headphones if they are connected. (page 6) No sound from the headphones. \ Check if the headphone plug is inserted properly into the jack. (page 6) Noise interferes. \ Turn nearby electrical appliances off. \ Install the audio system more apart from the TV set. Amplifier / Speaker section The clock display blinks without changing the figures. \ Adjust the present time again. (page 7) Timer operation is not possible. \ If the present time has not been adjusted or there was a power failure, adjust the present time. (page 7) \ Set the timer ON time and OFF time. (pages 54 to 60) \ Press the TIMER key on the remote to activate the timer. (pages 55, 57 and 59) Radio stations cannot be received. \ Connect the provided AM loop antenna to the AM ANTENNA jack. (page 5) \ Extend the FM rod antenna and orient it to the direction in which best reception is obtained. (page 5) \ Select the correct broadcast band. (pages 8 to 9) \ Tune to the frequency of the desired station. (page 9) After a radio station is preset, it cannot be received by pressing the 4 P.CALL or . P.CALL key. \ Preset stations with tunable frequencies. (pages 8 to 9) \ If the preset memory has b...