Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Tools required for installation Phillips screwdriver, Flat-head screwdriver, Clip driver, Pliers, Nippers, Wrench, Electric hand drill and bits, Cutting knife, Electrical tape, Scissors, Felt-tip pen Safety caution Be sure to observe the warning and caution provided below as they are critical for your safety. The meanings of the symbols are as follows. SEPARATE CUSTOM FIT SPEAKER K-ES01 INSTRUCTION MANUAL KENWOOD CORPORATION B54-1210-20 (FHP) Installation cautions If the product is handled erroneously by ignoring the instruction of this mark, fatal hazard or serious injury on human body may result. If the product is handled erroneously by ignoring the instruction of this mark, injury on human body, or damage of product may result. CAUTION Work depending to instruction manual. When installing or wiring the product, be sure to follow strictly the instruction and installation manuals of the product. (If the instructions are not observed strictly, the product may be displaced and hit you during braking and there may also be a risk of electric shock or fire hazard.) ? Please read thoroughly. Be careful not to damage the tank and electric wiring. In case the product is installed by making holes on the vehicle chassis, be careful never to damage the gasoline tank, piping, electric wiring or other parts of the vehicle. (Otherwise fire hazard may result.) Do not pull the cord. When you remove the connector, please remove and lock it with the connector main part, without pulling the cord. Otherwise disconnection of a cord and poor contact may result. Do not cut insulation tube in the middle of a power cord. Do not use power cord for other products by cutting insulation tube in the middle of a power cord. (Otherwise a shorting accident* may occur, which could result in fire accident.) Do not open the back and top covers of the product or modify it. (This may lead to fire hazard or other accident.) • For inspection and servicing, consult your dealer or nearest KENWOOD service agent or distributor. • Servicing by the user may lead to fire hazard or other accidents. Use a fuse with the specified rating. When the fuse is blown, first ensure that there is no short-circuiting* between the wired cords, then replace with a new fuse with the capacity (Ampere value) specified on the fuse box. (Using other fuse than specified may lead to fire hazard.) • For fuse replacement, refer to the owner's manual of your vehicle. Please check the spec. Use provided parts for installation. Be sure to install a product using provided parts. When parts other than the provided ones are used, a product may fall off and hit the passenger while driving, causing injury or product breakage. Inspect the vehicle after installation. After installation of the product, be sure to check that the brake lamps, head lamps, direction indicators, windshield wipers, power window, etc. of the vehicle function normally. (If any of the vehicle functions are damaged due to incorrect wiring , etc., traffic accident may result. ) Remove battery connection before work. Before installing or wiring anything, be sure to remove the cable from the negative terminal of the battery. (Otherwise a shorting accident* may occur, which could result in fire accident.) Remove negative terminal. Use proper tools for the processing objects. When tightening a bolt or nut, always be sure to use the tool matching its size. If the securing torque of a part is specified, be sure to secure it with the specified force. (Otherwise the bolt or nut may be damaged or detached during use.) Wrap cords with protective tape. The cords near metallic parts of the vehicle should be protected against sharp edge of the metallic parts by wrapping insulating tape around them. (If a cord is damaged, electric shock or short-circuiting* as well as fire hazard may result.) * Short-circuiting and shorting accident Short-circuiting refers to the direct connection between the positive and negative poles of electricity. This may occur when a stripped cord (electric wiring) comes in contact with another cord or metallic part of vehicle. Short-circuiting may produce spark, which may be caught by surrounding objects and result in fire hazard. Cautions on use WARNING Operate the car audio after stopping the vehicle. The car audio system should be operated after having stopped the vehicle in a safe place. (Operating it while driving a vehicle may lead to traffic accident.) Should any of the following abnormal phenomena is observed, immediately stop the use and operation of the product. • No sound output. • Water is spilt on the product. • A foreign object such as metal or a piece of paper gets inside the product. Do not use the product for other purpose than car use. This product has been designed for installation and operation in a vehicle. Do not use it for other purpose. (Otherwise imperfect installation may cause the product to drop and cause injury.) • The product starts smoking. • Abnormal noise or odor is prod...