Stimmen - 4, Durchschnittliche Bewertung: 4.8
(
)
)
|
Anleitung Zusammenfassung
Balanced audio interconnects utilize two conductors, while standard RCA audio interconnects use only a single "unbalanced" conductor. This enhanced design gives balanced audio interconnects the power to provide greater resistance against sources of noise (RF, EMI, etc.). The result is a more pure signal transfer, especially in longer-run applications. The industry standard NEUTRIK XLR connection is utilized due to their robust design and high performance. All internal wiring consists of twisted shielded wire. Your Oracle CD Player is equipped with: • BNC, output of 0,5 Volts peak to peak @ 75 Ohms • RCA analog output • XLR balanced analog outputs • Impedance < 100 Ohms • Recommended impedance load 50 kOhms (Minimum 5 kOhms) • Maximum effective output level, 2,4 Volts • Digital to Analogue converter type, Delta Sigma • Resolution 24 Bits You now have a choice of analog connections. You might even consider running both at the same time. To utilize the analog RCA capabilities, connect your pair of RCA terminated interconnect cables from the rear of the player to your preamplifier or integrated amplifier (CD INPUT). To utilize the analog balanced XLR connections, connect your pair of XLR terminated interconnect cables from the rear of the player to your preamplifier or integrated amplifier’s XLR inputs. Connection to the Pre-Amplifier, CD input • Connect your pair of RCA terminated Analogue Interconnect cables from the rear of the player to your pre-amplifier Digital input (CD input). Note: It is not necessary to use digital output unless connecting to a separate stand alone DAC. Note: We strongly suggest the use of the best possible Analogue Interconnect Simultaneous Connection of an External Digital to Analogue Converter It is possible to simultaneously use the BNC (75 Ohms) Digital output to compare the players internal Digital/Analogue converter, with that of an external (stand alone) D/A converter. • Plug your digital/optical interconnect to the rear of the player and connect it to your stand alone D/A converter. • Connect the Analogue outputs to an “Auxiliary” input at the rear of your pre-amplifier. • Balance the volume between the two D/A converters through the external converter volume control…should this facility be available. • Switch from “CD” to “Auxiliary” so as to compare the two options. Warning! Lower the volume of the pre-amplifier as there could be a major difference in gain, this could cause damage to your loudspeakers. POWER SUPPLY CONNECTION • Connect the 15 pin DC signal cable to the rear of the CD turntable and secure it with the two locking thumbs screws. • Connect the other end to the power supply and secure it as above. • Plug the AC power cord to the IEC socket at the power supply end, and the other end to the line voltage wall socket. • Turn the power supply “ON”, indicated by the line ( — ) on the rocker switch above the IEC socket, the red “L.E.D.” at the front of the power supply will now light up. The “OFF” position is indicated by ( 0 ) on the rocker switch. Important Warning! CLASS 1 Laser Product. It is essential that the protective top cover be installed and remains in place until the “No Disc” message appears in the CD display. This also applies should the unit be switched off during a listening session, NEVER remove this cover until the “No Disc” or the disc information message appears or re-appears after a new switch-on. THE MAGNETIC DISC CLAMP Operation • Place the compact disc on your Oracle CD turntable. • Install the magnetic disc clamp To Remove the Magnetic Disc Clamp (option 1) • Lift the compact disc by holding it from the periphery with the magnetic disc clamp installed. To Remove the Magnetic Disc Clamp (option 2) • Lift the magnetic disc clamp straight up. The compact disc will follow because of the adhesion of the Urethane vibration damping trap to the compact disc surface. Caution! Since the adhesion will diminish as the Urethane picks up dust, it is important to place your hand under the compact disc to prevent it from falling. Please read the recommended maintenance procedure below. • Peel the disc from the clamp, this will break the close seal between the Urethane vibration damping trap and the compact disc. Maintenance Your Oracle player is equipped with a very efficient magnetic clamp. One of the key features of this clamp is the proprietary Urethane compound ring that acts as a vibration damping tap. To obtain optimal performance, keep the surface of the Urethane vibration damping trap clean at all times using your Brilliance cleaner or denatured alcohol (mentholated spirits). To extend the cleaning cycle to a maximum, we recommended not setting the magnetic disc clamp with the Urethane facing down as dust would very quickly reduce the adhesion to the compact disc, thus lowering the vibration damping trap efficiency. SAFE OPERATING INSTRUCTIONS Please Follow these Important Safety Tips for The Safe Operation of your CD Player The main Power On/Off switc...
Dieses Handbuch ist für folgende Modelle:Stereoanlage - 2000 Transport (1.24 mb)
Stereoanlage - CD 2000 (1.24 mb)