Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Panasonic Dateigröße: 746.19 kb Dateiname: SL1200GLD.pdf Unterrichtssprache:

. . 9 Power switch (power) . . . . . . . . . . . . . . . . . . . . . . . . 8 Strobe light, pilot lamp . . . . . . . . . . . . . . . . . . . . . . . 8 Start-stop button (start-stop) . . . . . . . . . . . . . . . . . . 8 Speed select buttons (33, 45) . . . . . . . . . . . . . . . . . . 8 Shell stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Arm-height control . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Horizontal weight control knob . . . . . . . . . . . . . . . . 9 Balance weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Stylus pressure control . . . . . . . . . . . . . . . . . . . . . . . 6 Arm lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Anti-skating control . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Cue lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Arm clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Arm rest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Tone arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pitch indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Pitch control (pitch adj.) . . . . . . . . . . . . . . . . . . . . . . 9 Locking nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Head shell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Reset button (reset) . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Variable range pitch button (±16/±8) . . . . . . . . . . . . 9 Stylus light switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Stylus light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Controls Screws Stylus tip Overhang gauge Stylus weight Screws Head shell Lead wire Terminal Shell weight Stylus Cartridge RQT7021 5 1 Fit the turntable and turntable mat. Put the turntable on the center spindle and then lay the mat on top. •Be very careful when putting the turntable on the main unit. The magnet on the bottom of the turntable is finely adjusted and sharp contact can cause it to move and lead to poor operation. Ensure the magnet remains free from dust and iron particles. •Do not adjust the screws attaching the magnet to the turntable. The rated performance of the unit cannot be guaranteed if the magnet is moved. 2 Attach the head shell. Fit the head shell into the tone arm, keep it horizontal and tighten the locking nut. 3 Attach the balance weight to the rear of the tone arm. If the cartridge weighs between 10 and 13 grams, attach the included auxiliary weight to the main balance weight. Balance weight Putting the player together In order to prevent damage during shipping some of the equipment has been disassembled. Put the player together in the following order. •Do not connect the AC power supply cord until set up is complete. •Leave the dust cover off until set up and adjustments are complete. 1. Connect the PHONO earth lead and stereo PHONO cables to the amplifier PHONO terminals. Stereo connection cable White (L) Red (R) •If the earth lead isn’t connected, a hum will be heard from the AC power source. •You will not have adequate volume or sound quality if connecting to an amplifier that has no PHONO terminals. 2. Connect the AC power supply cord. •Connect this cord only after all other connections are complete. •Confirm the wattage of AC outlets on amplifiers and receivers before using them for this unit. This unit consumes 14.5 W. Locking nut Head shell 1 2 3 Magnet Screws Turntable mat Turntable Tone arm Center spindle TUNER SIGNAL GND PHONO (L) (R) 1 1 2 Amplifier (not included) This unit To household AC outlet Earth lead Stereo connection cable Connections and installation Connecting to an amplifier and AC power supply cord Auxiliary weight Connections and installation Connecting to an Audio Mixer (not included) Installation •Install the unit on a horizontal surface protected from vibrations. •Disconnect all units from the power source before making any con-•Keep this unit as far as possible from speakers. nections. •Reconnect the AC power supply cord after all other connections are complete. Unit •Ensure the unit is not exposed to direct sunlight, dust, humidity, Unit and heat from a heating appliance. •This unit may pick up interference from a radio if there is one nearby. Keep radios as far as possible from this unit. .... Earth lead Audio mixer Adjusting the height of the insulators Place the unit where it is to be used and adjust the height of the legs to make the unit horizontal. Preparatory adjustments Horizontal balance and stylus pressure 1 Release the tone arm. 1. Remove the stylus cover, taking care not to damage the stylus, then release the arm clamp. 2. Free the tone arm from the arm rest. Arm clamp 2 Adjust horizontal balance 1. Push the cue lever down. 2. Turn the anti-skating control to “0”. 3. Turn the balance weight until the arm is approximately horizo...

Herunterladen

Geben Sie zwei Ziffern: