Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
IN PARTICULAR WHEN STEREO SIGNALS ARE WEAK, IT IS PREFERABLE TO RECEIVE THE PROGRAM IN MONO. • SET THE FM STEREO MONO SWITCH (16) TO THE “STEREO” POSITION TO RECEIVE STEREO PROGRAMS. THE LED “ST” INDICATOR (6) WILL LIGHT UP TO SHOW THAT FM STEREO PROGRAM IS RECEIVED. HINTS FOR BEST RECEPTION: -AM: THE RECEIVER HAS A BUILT-IN AM BAR ANTENNA. IF AM RECEPTION IS WEAK, SLIGHTLY 4 ROTATING OR RE-POSITIONING OF THE UNIT WILL USUALLY IMPROVE THE AM RECEPTION. - FM: THE RECEIVER HAS A BUILT-IN FM WIRE ANTENNA (18). THIS WIRE SHOULD BE TOTALLY UNRAVELED AND EXTENDED FOR BEST RECEPTION. IF FM RECEPTION IS WEAK TRY REPOSITIONING THE FM WIRE ANTENNA UNTIL YOU FIND THE STRONGEST FM SIGNAL. PLAYING PHONO RECORDS 1. RAISE THE TURNTABLE DUST COVER. 2. REMOVE THE STYLUS PROTECTOR AND RELEASE THE TONE ARM CLAMP (14). 3. SET THE FUNCTION SELECTOR (5) TO “PHONO”. 4. PLACE A RECORD ON THE TURNTABLE, OVER THE CENTER SPINDLE. 5. SET THE SPEED SELECTOR SWITCH (13) TO 33, 45 OR 78 RPM ACCORDING TO THE RECORD YOU ARE PLAYING. PLACE THE INCLUDED 45 RPM ADAPTOR (12) OVER THE CENTER SPINDLE WHEN PLAYING 45 RPM RECORDS. 6. MOVE THE TONE ARM TO THE BEGINNING OF THE RECORD OR TO THE BEGINNING OF A PARTICULAR TRACK. GENTLY LOWER THE TONE ARM ONTO THE RECORD TO START PLAYING. 7. ADJUST THE VOLUME IF NEEDED. THE TURNTABLE WILL STOP AUTOMATICALLY WHEN THE RECORD FINISHES. 8. TO STOP THE RECORD BEFORE IT ENDS, LIFT THE TONE ARM AND RETURN IT CAREFULLY ONTO THE TONE ARM CLAMP (14). 9. REPLACE THE STYLUS PROTECTOR ON THE STYLUS WHEN NOT IN USE. IMPORTANT: I. DO NOT STOP OR TURN THE PLATTER MANUALLY. II. MOVING OR JARRING THE TURNTABLE WITHOUT SECURING THE TONE ARM CLAMP COULD RESULT IN DAMAGE TO THE TONE ARM. AUTO-STOP SWITCH OPERATION THE AUTO-STOP AREA ON SOME RECORDS MAY EXTEND BEYOND THE PRESET SETTING. AS A RESULT THE TURNTABLE COULD POSSIBLY STOP BEFORE THE LAST TRACK FINISHES. IF YOU EXPERIENCE THIS DURING PLAYBACK, SET THE AUTO-STOP SWITCH (15) LOCATED ON THE BACK OF THE UNIT TO THE “OFF” POSITION. THE TURNTABLE WILL NOW RUN TO THE END OF THE RECORD BUT WILL NO LONGER STOP AUTOMATICALLY. TO STOP THE TURNTABLE YOU WILL NEED TO EITHER SET THE FUNCTION SELECTOR (5) TO ANOTHER POSITION OTHER THAN PHONO OR RETURN THE AUTO-STOP SWITCH (15) TO THE “ON” POSITION. AFTER THE RECORD STOPS, LIFT AND RETURN THE TONE ARM CAREFULLY BACK ONTO THE TONE ARM CLAMP (14). 5 LISTENING TO TAPE PLAYBACK : SET THE FUNCTION SELECTOR (5) TO “TAPE”. LOAD CASSETTE TAPE INTO THE UNIT (LOCATED ON SIDE OF THE UNIT) PLAYBACK WILL AUTOMATICALLY BEGIN ADJUST THE VOLUME CONTROL (8) TO OBTAIN THE DESIRED SOUND LEVEL.. FAST FORWARD : PRESS BUTTON HALFWAY TO FAST FORWARD THE TAPE. PRESS BUTTON LIGHTLY AND PLAYBACK WILL RESUME. STOP AND EJECTION : PRESS BUTTON ALL THE WAY TO END PLAYBACK AND EJECT TAPE. REMARK: - MAKE SURE THE TAPE DIRECTION IS CORRECT WHEN INSERTING IT INTO THE CASSETTE DECK. - IT IS RECOMMENDED TO REMOVE THE CASSETTE TAPE FROM THE SYSTEM EVERY TIME AFTER FINISHED LISTENING. DO NOT LEAVE THE CASSETTE TAPE INSIDE THE SYSTEM WHEN NOT IN TAPE PLAYBACK MODE. LINE OUT OPERATION FOR BETTER PLAYBACK SOUND, YOU CAN CONNECT THE SB6052 TO AN EXTERNAL AUDIO AMPLIFIER VIA THE RCA LINE OUT JACKS LOCATED ON THE BACK PANEL. PLEASE PROCEED AS FOLLOWING: 1. CONNECT THE “L” & “R” LINE OUT JACKS AND THE AUX IN OF YOUR AUDIO AMPLIFIER. (CONNECTION CABLE IS NOT INCLUDED). 2. SELECT THE MUSIC SOURCE BY SETTING THE FUNCTION SELECTOR (5) TO “PHONO”, “TAPE”, “AM”, “FM” OR “FM ST” AS DESIRED. 3. TURN ON THE EXTERNAL AMPLIFIER. 4. SOUND WILL THEN COME OUT FROM THE SYSTEM’S BUILT-IN SPEAKERS AND THE EXTERNAL AMPLIFIER’S SPEAKERS SIMULTANEOUSLY. 5. SET THE VOLUME CONTROL (8) TO “MIN” AND ADJUST THE SOUND LEVEL USING THE VOLUME CONTROL ON THE EXTERNAL AMPLIFIER AS DESIRED. 6. TURN THE SYSTEM AND THE EXTERNAL AMPLIFIER OFF WHEN YOU HAVE FINISHED LISTENING. 7. UNPLUG THE CONNECTION CABLE. 6 STYLUS REPLACEMENT PLEASE REFER TO THE DIAGRAM BELOW TO REPLACE THE STYLUS. NO ADDITIONAL STYLUS IS SUPPLIED WITH THE SYSTEM. (1) Loosen the red part of stylus (2) Replace with the new stylus by screw driver and take out (not included) as diagram C as diagram A and B. and D. CARE AND MAINTENANCE CLEAN YOUR UNIT WITH A DAMP (NEVER WET) CLOTH. SOLVENT OR DETERGENT SHOULD NEVER BE USED. 1. AVOID LEAVING YOUR UNIT IN DIRECT SUNLIGHT OR IN HOT, HUMID OR DUSTY PLACES. 2. KEEP YOUR UNIT AWAY FROM HEATING APPLIANCES AND SOURCES OF ELECTRICAL NOISE SUCH AS FLUORESCENT LAMPS OR MOTORS. 3. ALWAYS CLEAN THE OUTSIDE OF THE CABINET THOROUGHLY IF IT BECOMES WET WITH MOISTURE OR WATER SPLASHES. THIS WILL HELP TO PROTECT THE INTERNAL PARTS OF THE UNIT FROM ENTRY OF WATER AND POSSIBLE MOISTURE DAMAGE. TROUBLESHOOTING GUIDE SHOULD YOU EXPERIENCE DIFFICULTIES IN THE USE OF THIS PLAYER PLEASE REFER TO THE FOLLOWING CHART OR CALL 1-800-777-5331 FOR CUSTOMER SERVICE. PROBLEM POSSIBLE CAUSE REMEDY THE UNIT WILL NOT • THE UNIT IS DISCONNECTED FROM THE AC OUTLET • CONNECT TO AN OUTLET. PLAY • THE AC OUTLET HAS NO POWER • TRY THE ...