Stimmen - 5, Durchschnittliche Bewertung: 3.4
(
)
)
|
Anleitung Zusammenfassung
The TTB-2500 requires some assembly. Please read the following instructions before installing or using your new unit. The TTD-2500 has a 2 year limited warranty! CAUTION! -Keep this device away from rain and moisture! Name of Parts 1. 45-rpm Adapter 2. Turntable Platter 3. Center Spindle 4. Power Switch 5. Start/Stop Button 6. Strobe Dots 7. Target Light 8. LED display for speed indication Green LED: pitch control (11) is in center click position and the speed is quartz-controlled. Red LED: pitch control (11) is not in center position. 9. Headshell 10. Speed Select Buttons 11. Pitch Adjustment (+/-10%) 12. Pitch Control Slider 13. Tonearm 14. Anti-skate Knob 15. Counterweight 16. Spare phono cartridge slot 17. Hinge for dust cover 18. Trim control for changing the range of the pitch adjustment (11, 12). 19. Right RCA output jack (red) 20. Left RCA output jack (white) 21. Ground (GND) 22. Remote Start/Stop 1/4” output jack 23. Beat output for Beat Analyser R L GND REMOTEBEAT 2223212019 Before Use Check for the following parts included in the package with the main unit. • Turntable Platter • Slip mat • Dust Cover • 45-rpm adapter • Counterweight • Headshell • User instructions NOTES: • Do not connect the AC power plug before assembly has been completed. • Before turning the power on, make sure once again all the connections and power voltage settings are correct. Always turn off the power when connecting or disconnecting. • Read this manual carefully before using the unit. Be sure to store the manual in a safe place for future reference. Warranty & Service The TTB-2500 has a 2 year limited warranty. Mail in warranty card as soon as possible. BACK PANEL For service, contact your local American DJ® Dealer. TTB-2500 User Instructions page 2 User Instructions Assembly 1. Remove the main unit with the packing from the box and take off the packing. 2. Set the 45-rpm adapter on the main unit. 3. Inset the turntable platter onto the center spindle. 4. Set the slip mat on the platter. 5. Installation of cartridge: When installing a cartridge, refer to the operating instructions of that cartridge. During installation, attach the stylus protector to guard the stylus tip from damage. (a) Connect the lead wires to the cartridge terminals. The terminals of most cartridges are color coded. Connect each lead wire to the terminal of the same color. WHITE (L+)..............Left channel+ BLUE (L-)..............Left channel- RED (R+)..............Right channel+ Green (R-)..............Right channel (b) Install the cartridge to the headshell and tighten it with screws provided with the cartridge. 6. Inset the headshell into the front end of the tonearm, then turn the lock nut counterclockwise with the headshell firmly held horizontally. 7. Slide counterweight onto tonearm. Twist it lightly and it will screw onto the rear shaft of the tonearm. 8. Adjustment of horizontal zero (0) balance and stylus pressure: (a) Remove the stylus protector, do not touch the stylus tip during the adjustment. (b) Set the cueing lever to the lower position. (c) Release the arm clamp and lift the tonearm from the arm rest to free it. (d) Rotate the counterweight until the tonearm is approximately balanced horizontally (floats freely). (e) Refasten the tonearm with the arm clamp. (f) Hold the counterweight stationary with one hand and rotate only the stylus-pressure ring to bring the number “o” of the ring into alignment with he center line on the tonearm rear shaft. (g) Rotate the counterweight counterclockwise until the scale shows the value corresponding to the pressure of the used stylus. The stylus pressure of the installed pick-up system is 2g. Should you use a separate pick-up system, please follow the manufacturer’s instruments. 9. Set the anti-skating control knob to the same value as the stylus pressure. 10. Install the dust cover to the main unit. Placement • Do not place the unit in a location where it will be exposed to direct sunlight or near a heating appliance. • Do not place the unit in a location where there is high humidity or a lot of dust. • Cartridge may pick up slight sound pressure or vibrations of the speakers coming along the floor or though the air resulting in howling. Find a location which is very stable and vibration free. • The legs have functions for adjusting the height of the unit itself. Adjust the legs to stabilize the main body horizontally. Connections 1. Connect the power cord to the auxiliary power outlet on the rear panel of your amplifier or receiver or to a household AC outlet. 2. Connect the unit output terminals to the the PHONO jack of your American DJ Mixer or receiver. Output terminals Mixer (Receiver) L (White) (18) ---------------------------->L Channel R (Red) (19) -----------------------------> R Channel GND (Spade) (21) ---------------------> Ground NOTE: Be sure to connect the ground terminals firmly to the Mixer or receiver. If this connection is not made or is loose, a power source “HUM” will resu...