Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
To adjust the sound level of the connected source The input sensitivity level of each function can be adjusted (except the TUNER, CD(DIGITAL), VIDEO 1 (DIGITAL), VIDEO 2 (DIGITAL) and VIDEO 3 (DIGITAL) functions). When the sound level of the connected source is higher or lower than that of the TUNER, adjust it as follows. 1 Select the function to be adjusted. Turn the FUNCTION or press the TAPE MONITOR button and play the source. 2 Press the N(UP) or M(DOWN) button repeatedly. Adjust the level so that the “OVER LEVEL” indicator does not light on the display. • The level can be adjusted between -6dB (MIN) and +8dB (MAX) in 2dB steps. Adjust the level so that the sound is output at the same level as the TUNER. • The input sensitivity level of the TAPE MONITOR can be adjusted to 0dB or -6dB. 11 ENGLISH TO PLAY A DVD OR LD RECORDED IN RECORDING AN AUDIO SOURCE DOLBY DIGITAL OR DTS SURROUND This receiver is equipped with the Dolby Digital decoder and DTS decoder, and has the DIGITAL IN (both OPTICAL and COAXIAL) terminals. When a DVD or LD player is connected to the DIGITAL IN terminal of the receiver, you can enjoy theater- quality audio right in your home when playing discs recorded in Dolby Digital surround or DTS surround. Before operation • Check that the TAPE MONITOR is not selected. If the TAPE MONITOR is selected, press the TAPE MONITOR button so that “TAPE OFF” appears on the display. • When connecting an LD player equipped with the AC-3 RF OUT terminal, use an RF demodulator unit. Also connect the analog AUDIO OUT terminals of the LD player to the receiver to play all the sources. For further information, refer to the instructions of the LD player. 1 Turn the FUNCTION to select theVIDEO 1 (VIDEO 2 or VIDEO 3) and press the DIGITAL/ANALOG/ BAND button repeatedly until “DIGITAL” is displayed. The DVD (LD) player connected to the OPTICAL (COAXIAL) DIGITAL IN terminal is selected as a source. 2 Start playing the DVD (LD) recorded in Dolby Digital surround or DTS surround. • The “DOLBY DIGITAL” indicator will light on the display when the bit stream of the Dolby Digital surround comes in the unit. To select the Dolby Digital surround mode according to your speakers, see “SELECTING DOLBY SURROUND” on page 15. • The “dts” indicator will light on the display when the bit stream of the DTS surround comes in the unit. To select the DTS surround mode according to your speakers, see “SELECTING DTS SURROUND” on page 19. NOTE • While the TAPE MONITOR is selected and the TAPE MONITOR indicator turns red, “DIGITAL” cannot be selected. • When headphones are plugged in, the Dolby Digital surround mode or DTS surround mode is automatically changed to “2chSTEREO” and the “2CH DOWNMIX” indicator lights on the display. Even if the SURROUND button is pressed while the headphones are plugged in, the mode cannot be changed. • This unit supports input signals of the Dolby Digital surround bit stream, DTS surround bit stream and linear PCM whose sampling frequency is 32 kHz, 44.1 kHz, 48 kHz and 96 kHz. • When connecting some DVD players to the receiver through the DIGITAL IN terminals, noise may be heard in the DVD operation: e.g. searching a disc, skipping a chapter. 1 Select the program source to be recorded. Turn the FUNCTION. 2 Set the tape deck or MD recorder to the recording mode. 3 Start the selected program source. To monitor recorded sound during recording (when the connected tape deck is a three-head system) Press the TAPE MONITOR button. “TAPE ON” appears on the display for four seconds, and then the source name selected in step 1 comes back on. To cancel the tape monitor, press it again so that “TAPE OFF” appears. NOTE • Any sound control system has no effect on recording (see page 8). • Input sound through the DIGITAL IN terminals cannot be recorded. When recording the sound from the DVD, CD, MD or LD player, connect the analog AUDIO OUT terminals of the player to the corresponding AUDIO IN terminals of the receiver. The sound will be recorded in 2 ch stereo. • When recording audio sources by the MD recorder connected to the VIDEO 1/DVD/MD AUDIO OUT terminals, the selected video source (see page 11) should be V2 or V3. Recording cannot be done while the V1 (VIDEO 1) is selected and displayed on the window. • Input sound from the tape deck connected to the TAPE MONITOR IN terminals cannot be recorded. To play a DTS audio CD There are some audio CDs recorded in DTS surround like DVDs and LDs. They will present you with a live-quality audio in your home. 1 Select the CD function. 2 Select the DIGITAL mode (see page 11). The CD player connected to OPTICAL DIGITAL IN (CD) terminal is selected as a source. 3 Start playing the CD recorded in DTS surround. To select the DTS surround mode, see page 19. BASIC OPERATIONS EnEnEnEnEn ENGLISH 12 RADIO RECEPTION RADIO RECEPTION MANUAL TUNING When the reception contains noise interference Move the unit away from other electrical appliances, especially digital audio devices, or tur...