Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
To stop the search manually, press ror t. When an FM stereo broadcast contains noise Press MODE on the remote control so that “MONO” is displayed. Noise is reduced, although reception is monaural. To change the AM tuning interval The default setting of the AM tuning interval is 10 kHz/ step. If you use the unit in an area where the frequency allocation system is 9 kHz/step, change the interval as follows. 1 Press TUNER/BAND. 2 Press POWER 6STANDBY/ON while pressing TUNER/BAND. When the AM tuning interval is changed, the preset stations are cleared. NOTE If the unit picks up noise from other electrical appliances nearby, like a TV or fluorescent lights, move the unit. To listen with the headphones Connect headphones with a stereo mini plug to the PHONES jack. 6 ENGLISH 0-9, +10 MODE EQ aPAUSE VOLUME k, is BAND DISPLAY r, tcPLAY 0-9, +10 MODE EQ aPAUSE VOLUME k, is BAND DISPLAY r, tcPLAY PRESETTING STATIONS You can preset up to 15 stations in each band. 1 Select a station. 2 Press *aPAUSE/SET once so that “MEMO” flashes to store the station. A station is assigned a preset number, beginning from 1 in consecutive order for each band. Preset number Frequency * or aPAUSE on the remote control 3 Repeat steps 1 and 2. The next station will not be stored if a total of 15 preset stations have already been stored for a band. To listen to preset stations Select a band then press dPLAY/DIR/PRESET repeatedly. cPLAY on the remote control is also available. To select a preset number directly with the remote control Press the numbered buttons 0-9 and +10. Example: To select number 15, press +10 and 5. To select number 10, press +10 and 0. To clear a preset station Select the preset number first. Press s, and press a within 4 seconds. The higher numbers in the band are decreased by one. En SOUND ADJUSTMENT Volume or tone adjustment does not affect recording. VOLUME/TIMER (VOLUME) Turn VOLUME/TIMER, or press VOLUME kor i on the remote control. The volume level is displayed as a number 0 to 25 (MAX). • The volume level is automatically set to 14 if the power is turned off when the volume level is set to 15 or more. • Pressing DISPLAY on the remote control displays the adjusted volume level. *3-MODE EQ (equalizer) Press 3-MODE EQ repeatedly until the desired mode is displayed. The equalizer mode changes to ROCK, POP, JAZZ or no equalization, cyclically. ROCK - Emphasizes the high and low range of music. POP - Emphasizes voice and midrange of music. JAZZ - Emphasizes the low range of music. * or EQ on the remote control T-BASS system The T-BASS system enhances the realism of low- frequency sound. Press T-BASS to turn it on or off. QSURROUND system The QSURROUND system built into this unit uses only two speakers at the left and right to create an atmosphere that sounds as if you are surrounded by two front speakers and two rear speakers. Press QSURROUND to turn it on or off. • The QSURROUND system does not work for monaural sources. • At higher volumes, turning QSURROUND on may cause sound distortion. In this case, make the volume down. ENGLISH 7 POWER 6STANDBY/ON a PAUSE/SET s STOP/CLEAR r, td PLAY/DIR/PRESET CD CD OPEN/ CLOSE POWER 6STANDBY/ON a PAUSE/SET s STOP/CLEAR r, td PLAY/DIR/PRESET CD CD OPEN/ CLOSE CD OPERATIONB 1 Press CD. The power is turned on. 2 Press CD OPEN/CLOSE to open the disc compartment. Set a disc with the printed side up, then press CD OPEN/CLOSE to close the disc compartment. Total number of tracks and total playing time are displayed. It will take about 15 seconds when loading a CD-RW disc. 3 Press dPLAY/DIR/PRESET to start play. The number of the track being played and elapsed playing time are displayed. To remove the disc Open the disc compartment. Pick up the disc, holding its edge, while pressing the center pivot gently. sSTOP/CLEAR – Stops play. aPAUSE/SET – Pauses play. To resume play, press again. r,t– Searches for a particular point during playback. Hold down ror tand then release it. – Skips to the beginning of a track. Press ror trepeatedly. To start play when the power is off, press CD. The power is turned on and play of the loaded disc begins (Direct Play Function). To select a track directly with the remote control, press the numbered buttons 0-9 and +10. CD play starts from the selected track and continues to the last track. Example: To select number 25, press +10, +10 and 5. To select number 10, press +10 and 0. After listening, press POWER 6STANDBY/ON to turn the power off. NOTE • Do not use irregular shape CDs (example: heart- shaped, octagonal ones). It may result in malfunctions. • Do not place more than one disc in the disc compartment. • Do not touch the lens. Doing so may cause malfunctions. • The unit may not play a CD-R/RW disc that is recorded on personal computers or some kinds of CD-R/RW recorders because of differences in recording platforms. • Do not attach any seal or label to either side (the recordable side or the labeled side) of a CD-R/RW disc. It may cause malfunction. ...