Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Electrolux Dateigröße: 327.24 kb Dateiname: cf146.pdf Unterrichtssprache:

• Clean the interior surface with lukewarm water using a soft cloth. Installing Your Freezer • This appliance is designed to be free standing only, and should not be recessed or built-in. • Place your freezer on a floor that is strong enough to support the freezer when it is fully loaded. • Allow 5 inches of space between the back and sides of the freezer, which allows the proper air circulation. • Locate the freezer away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Extreme cold ambient temperatures may also cause the freezer not to perform properly. • Avoid locating the freezer in moist areas. • Plug the freezer into an exclusive, properly installed-grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician or an authorized Avanti Products service center. • After plugging the appliance into a wall outlet, allow the unit to cool down for 2~3 hours before placing food in the freezer compartment. Electrical Connection This freezer should be properly grounded for your safety. The power cord of this freezer is equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the possibility of electrical shock. Do not under any circumstances cut or remove the third ground prong from the power cord supplied. This freezer requires a standard 115/120Volt~60Hz electrical outlet with three-prong ground. The cord should be secured behind the freezer and not left exposed or dangling to prevent accidental injury. Never unplug the freezer by pulling the power cord. Always grip the plug firmly and pull straight out from the receptacle. Do not use an extension cord with this appliance. If the power cord is too short, have a qualified electrician or service technician install an outlet near the appliance. The light indicates that the freezer is properly connected to the electrical power. The light indicates power supply, and will glow even if the temperature control dial is turned to “OFF”, or the compressor has failed to work and the compartment is not being cooled. .Warning. Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it replaced by an authorized Avanti Products service center. OPERATING YOUR FREEZER Temperature Control • Your freezer has one control for regulating the temperature. The temperature control is located on the lower right hand corner. • The first time you turn the unit on, switch the thermostat to the “MAX” setting and run for at least 2 hours before putting frozen foods inside. This will ensure the cabinet is thoroughly chilled before food is put in. • The range of the temperature control is from position"MIN" the warmest to "MAX" the coldest. Adjust the temperature control to the setting that best suits your needs. The setting of “MID” should be appropriate for home or office freezer use. • To turn the freezer off, turn the temperature control to "OFF". NOTE: • Turning the temperature control to "OFF" position stops the cooling cycle but does not shut off the power to the freezer. • If the unit is unplugged, lost power, or turned off; you must wait 3 to 5 minutes before restarting the unit. If you attempt to restart before this time delay, the freezer will not start. • Large amounts of food will lower the cooling efficiency of the appliance. • If you choose to change the thermostat setting, adjust thermostat control by one numerical increment at a time. Allow several hours for temperature to stabilize between adjustments. Defrosting Your Freezer • When? For the most efficient operation and minimum energy consumption, defrost the freezer when the frost on the freezer walls is excessive or . to . inch thick. • Choose a time when the stock of frozen food is low. CAUTION Do not use boiling water because it may damage the plastic parts. In addition, never use a sharp or metallic instrument to remove frost as it may damage the cooling coils and will void the warranty. We recommend using the plastic scraper provided with your unit. • Remove the frozen food from the freezer and place it in a cooler to protect the food. • Turn the thermostat knob to “OFF”. • Unplug the freezer. The Power Supply light should be off (amber light out). • During defrosting, the ice melts into the cabinet. • Remove the drain plug on the inside floor of the freezer by pulling straight out. • Place a shallow pan outside drain outlet. The defrost water will drain out. • Check the pan occasionally so the water does not overflow. • Clean the interior of the freezer. • Replace the plug on the inside floor. • Reset the thermostat to desired setting. • Allow the cabinet to cool for one hour. • Return food to the freezer. HELPFUL HINT: Defrosting usually takes a few hours...

Herunterladen

Geben Sie zwei Ziffern: