Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Frigidaire Dateigröße: 372.08 kb Dateiname: vm165w.pdf Unterrichtssprache:

This will reduce the possibility of a malfunction in the cooling system from handling during transportation. • Clean the interior surface with lukewarm water using a soft cloth. • In case the interior accessories are not correctly placed, rearrange them as described in chapter “Parts and Features” . Installation of Your Appliance • Place your appliance on a floor that is strong enough to support the appliance when it is fully loaded. To level your appliance, adjust the legs at the front of the appliance. • Allow 5 inches of space between the back and sides of the appliance, which allows the proper air circulation to cool the compressor. • Locate the appliance away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Extreme cold ambient temperatures may also cause the appliance not to perform properly. • Avoid locating the appliance in moist areas. Too much moisture in the air will cause frost to form quickly on the evaporator requiring more frequent defrosting of the appliance. . Electrical Connection This appliance should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the possibility of electrical shock. Do not under any circumstances cut or remove the third ground prong from the power cord supplied. Plug the appliance into an exclusive properly installed-grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and or grounding should be directed toward a certified electrician or an authorized Avanti Products service center. Use of extension cords is not recommended. This appliance requires a standard 115/120-volt, 60Hz electrical outlet with three-prong ground. The cord should be secured behind the appliance and not left exposed or dangling to prevent accidental injury. .Warning. Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it replaced by an authorized Avanti Products service center. . Reversing the Door Swing of Your Appliance This appliance has the capability of either opening the door from the left or right side. The unit is delivered to you with the door opening from the left side. Should you desire to reverse the opening direction, please call customer service for reversal instructions. OPERATING YOUR FREEZER . Temperature Control (MODEL VM165 – ONLY) . Temperature Selector (MODEL VM165 – ONLY) • The temperature control is located on the front side of the cabinet. • The first time you turn the unit on set the temperature control to the “SUPER” position. (you may use a coin or flathead screwdriver.) After 4 hours, move the control to the MAX setting. • The range of the temperature control is from position" MIN" the warmest to “SUPER” the coldest. After 24 to 48 hours, adjust the temperature control to the setting that best suits your needs. The setting of “NORM” should be correct for home or office freezer use. NOTE: . If the unit is unplugged, power lost, or turned off; you must wait 3 to 5 minutes before restarting the unit. If you attempt to restart before this time delay, the freezer will not start. . Defrosting Your Freezer • When? For the most efficient operation and minimum energy consumption, defrost the appliance compartment when the frost on the appliance walls is excessive or . inch thick. • A few hours before defrosting set the thermostat to position MAX, so foods are well frozen. • Disconnect the power supply. • Remove the frozen food from the appliance and place it in a cooler to protect the food. • Leave the door open for a while so that you can easy scrape off the frost. • Use a plastic scraper but be careful not to damage the inner surfaces of the freezer. Wipe up the scraped frost and ice before it is completely defrosted. CAUTION • Do not use boiling water because it may damage the plastic parts. In addition, never use a sharp or metallic instrument to remove frost as it may damage the cooling coils and will void the warranty. We recommend using the plastic scraper. HELPFUL HINT Defrosting usually takes a few hours. Leaving the door open will help speed the process. Also, pouring warm water (not boiling) on the ice/frost will help speed melting. If you must use a scraper- please use caution - i...

Herunterladen

Geben Sie zwei Ziffern: