Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Frigidaire Dateigröße: 345.73 kb Dateiname: 398vfyw.pdf Unterrichtssprache:

Junked or abandoned appliances are still dangerous... even if they will "just sit in the garage a few days." • Before you throw away your old freezer: Take off the door. Leave the shelves in a place so that children may not easily climb inside. • Never allow children to operate, play with, or crawl inside the appliance. • Never clean appliance parts with flammable fluids. The fumes can create a fire hazard or explosion. • Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other appliance. The fumes can create a fire hazard or explosion. -Save these instructions- lnstallation Instructions > Before Using Your Freezer • Remove the exterior and interior packing. • Check to be sure you have all of the following parts: ■ 4 Baskets ■ 1 Instruction Manual • Before connecting the freezer to the power source, let it stand upright for approximately two hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation. • Cleaning the interior surface with lukewarm water using a soft cloth. ^ Installation of Your Freezer • Place your freezer on a floor that is strong enough to support the freezer when it is fully loaded. To level your freezer, adjust the legs at the front of the freezer. • Allow 5 inches of space between the back and sides of the freezer, which allows the proper air circulation to cool the compressor. • Locate the freezer away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Extreme cold ambient temperatures may also cause the freezer not to perform properly. • Avoid locating the freezer in moist areas. Too much moisture in the air will cause frost to form quickly on the evaporator requiring more frequent defrosting of the freezer. • Plug the freezer into an exclusive properly installed-grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and or grounding should be directed toward a certified electrician or an authorized Avanti Products service center. — 5 - *■* Electrical Connection H Warning H Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it replaced by an authorized Avanti Products service center. This freezer should be properly grounded for your safety. The power cord of this freezer is equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the possibility of electrical shock. Do not under any circumstances cut or remove the third ground prong from the power cord supplied Use of the extension cord is not recommended. This freezer requires a standard 115 volt, 60Hz electrical outlet with three-prong ground. The cord should be secured behind the freezer and not left exposed or dangling to prevent accidental injury. > Reversing the Door Swing of Your Freezer This freezer has the capability of either opening the door from the left or right side. The unit is delivered to you with the door opening from the left side. Should you desire to reverse the opening direction, please follow these instructions. NOTE: All parts removed must be saved to do the reinstallation of the door. Reversal and Installation of the Freezer Door • Remove the two screws(1 )that hold the lower hinge(2)(right side)to the frame. Also, remove the screw-type leveling front leg(3). • Remove the left front leg(4) and transfer it to the right side. • Lift the door and place it on a padded surface to prevent scratching it. Make sure to remove the spring(5) located inside the upper right hole of the door and the upper right side pin(6). • Remove the plug button(7)from the upper left hole of the door and transfer it to the uncovered hole at the right side. Be sure to press the button firmly into the hole. • Insert the upper pin(6) previously removed from the right side (step 3) and transfer it to the other hole at the left side of the top frame. • Insert the spring(5)previously removed(step 3)inside the upper left side hole of the door. • Set the door in its place making sure the pin(6)enters the bushing at the lower upper frame s...

Herunterladen

Geben Sie zwei Ziffern: