Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
• Use a power cable that is properly grounded. Always use the appropriate AC cord certified for the individual country. Some examples are listed below: USA UL Switzerland SEV Canada CSA Britain BASE/BS Germany VDE Japan Electric Appliance Control Act 5. Connect the power cable to the AC/DC supply. Connect the other end to the appropriate AC outlet. Figure 12. Connecting the M170 Cables to your Computer 65-2223 You should be sure all cable connections are secure -- tighten all cable screws. Shaking and vibration may dislodge cables that are improperly connected. Route all wiring and cabling away from heat sources and sharp metal edges to avoid damage. Also, keep the touch screen cable away from sources of electromagnetic and radio frequency interference. WARNING To avoid the risk of electric shock which could result in serious injury or death: • Do not use a damaged power supply. • Do not use a power cord that is frayed or otherwise damaged. Testing the M170 FPD Note: The M170 FPD has a power status LED located on the front of the bezel. After connection, turn on the power switch located on the front bezel. Before you test your touch monitor, make sure all cables are connected properly and routed through the cable management system. Be sure to tighten all cable screws. To test that the monitor is working properly: 1. Turn on your computer. 2. Make sure the video image is displayed. If it is not, turn on your monitor. Ensure the LED is green – orange indicates power but no signal. 3. Make sure the video image is centered within the screen area. Use the monitor controls to adjust the image, if necessary. Perform an Auto Config first, then if you wish you can adjust the horizontal and vertical position, contrast, and brightness to better suit your video card and your personal preference. Refer to Chapter 3 for more information on using the on-screen menu to adjust the video display. Installing TouchWare™ Software TouchWare™ software includes the touch screen driver and control panel that enables your touch screen to work with your computer. When you install the CD included with your monitor, TouchWare™ will automatically load the correct driver for your system. 3M Touch Systems currently supports touch screen drivers for the following PC operating systems: • Windows XP (serial and USB) • Windows 2000 (serial and USB) • Windows NT 4.0 (serial only) • Windows 9x (serial and USB (Windows 98 only)) • Windows Me (serial and USB) These drivers and relevant technical documentation, can be found on the latest 3M Touch Solutions CD (19-640) and are also available for download from our website at After the software is installed, restart your computer to load and activate the touch screen driver. To complete the setup of your touch monitor, make sure you calibrate the touch screen. Calibrating the Touch Screen After you connect your touch monitor and install TouchWare™ software, you must calibrate the touch screen. Calibration serves two purposes: • Sets the active area of the touch screen • Aligns the touch screen’s active area to the underlying video To calibrate the touch screen, open the touch screen control panel and select Calibrate. Follow the directions displayed on the screen. For more information on calibration, refer to the online help or the user documentation. CHAPTER 3 Video Display Options This chapter provides guidelines for adjusting the video display and using the monitor controls to adjust the image to your liking. Before you make any adjustments: • Be sure to adjust the controls in your normal lighting conditions. • Display a test image or pattern whenever you adjust the video. Adjusting the M170 Video Display Your M170 FPD monitor has four main controls to adjust the video display. Three of these buttons are actually hot keys meaning that if the MENU key is not pressed first, these buttons control VOLUME, AUTO ADJUST, and BRIGHTNESS instantly. Figure 13. Video Display Controls • MENU – Shows or hides the menu. • SELECT -- Highlights the current menu option or saves the current setting. Press > or < to change the value. • /Right -- Enables you to scroll forward through items on the menu -- increase the value of selected option or move to the next menu item. Line Callout 2 (No Border): POWER Line Callout 2 (No Border): AUTO ADJUST Line Callout 3 (No Border): BRIGHTNESS Line Callout 2 (No Border): SELECT Line Callout 3 (No Border): VOLUME ADJUST Line Callout 2 (No Border): MENU Text Box: HOT KEYS Line Callout 2 (No Border): LED Line Callout 2 (No Border): 4/RIGHT Line Callout 2 (No Border): ?/LEFT If you do not press the Menu, Select, or /right adjust buttons for 45 seconds, the monitor adjustment program times out and hides the menu options. You can press the Menu button at any time to display the options again. Pressing MENU will ...