Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
diskettes. To insert a PCMCIA card, align the card with the socket and slide the car. into the socket until it locks into place. Note that some PCMCIA memor. cards must be prepared by your operating system before you can use the. for data storage. See your PCMCIA card manual for details. To eject a PCMCIA card, first ensure that the panel PC is not accessin. the memory card or device. Then press the appropriate eject button on th. socket. When the card pops out of the socket, remove it and store i. properly. PCMCIA socketPCMCIA cardEject button Figure 3-3: Inserting and ejecting a PCMCIA car. PPC-150 User's Manual USBkeyboardPrinterNetworkPS/2mouseUSBkeyboardPrinterNetworkPS/2mouse Figure 3-4: Using the I/O interface (upper level ports excluding COM ports. Chapter 3 Using the Panel PC MicrophoneHeadphonesCD-ROMplayerJoystickCRTmonitor SerialmouseMicrophoneHeadphonesCD-ROMplayerJoystickCRTmonitor Serialmouse Figure 3-5: Using the I/O interface (lower level ports and COM ports. PPC-150 User's Manual 3.. PS/2 Mouse and Keyboar. If you wish to use a full-size desktop keyboard and PS/2 mouse with you. panel PC, follow these instructions. 1. Be sure the panel PC is turned off. 2. Connect the Y-shaped adapter to the PS/2 mouse and keyboard port o. the rear bottom side of the rear cover. (See Fig. 3-4 and Fig. 2-6.. 3. Attach the keyboard to the 5-pin port of the Y-shaped adapter. 4. Attach the PS/2 mouse to the 6-pin female PS/2 port of the Y-shape. adapter. 5. Turn on the panel PC. 3.. PCI/ISA Bus Expansio. The panel PC supports PCI and ISA bus expansion cards. To integrate . new PCI or ISA bus card into your system, follow these instructions. 1. Turn off the panel PC. 2. Unscrew the two screws on the top of the PCI/ISA bus expansion slo. cover, and remove this cover. 3. Remove the metal plate by unscrewing the single attaching screw. 4. Insert the PCI or ISA bus card into the PCI/ISA slot of the riser card. (See Fig. 3-6 overleaf.. 5. Run the setup program within your operating system to configure you. system. Chapter 3 Using the Panel PC 28 PPC-150 User's Manual Figure 3-6: PCI/ISA bus expansion PCI/ISA bus card Metal plate PCI/ISA expansion slot cover 3.. Parallel Por. The panel PC supports the latest EPP and ECP parallel port protocols fo. improved performance and versatility with compatible printers or othe. devices. To connect the panel PC to a printer or other devices. 1. Be sure both the panel PC and the printer/devices are turned off. 2. Connect the 25-pin male connector of the printer cable to the 25-pi. female port on the panel PC labelled "parallel port". 3. If necessary, attach the other end of your printer cable to your printer. and fasten any retaining screws. A typical parallel printer connection i. illustrated in Fig. 3-4. 4. Turn on the printer and any other peripheral devices you may hav. connected to the panel PC, and then turn on the panel PC. 5. If necessary, run the panel PC's BIOS setup program to configure th. parallel port to respond as required by your printer and softwar. operating environment. 3.. Serial COM Port. There are four serial COM ports on the bottom of the rear cover. You ca. easily attach a serial device to the panel PC, such as an external modem o. mouse. Follow these instructions. 1. Be sure the panel PC and any other peripherial devices you may hav. connected to the panel PC are turned off. 2. Attach the interface cable of the serial device to the panel PC's seria. port. (See Fig. 3-5.) If necessary, attach the other end of the interfac. cable to your serial device. Fasten any retaining screws. 3. Turn on any other peripheral devices you may have connected to th. panel PC, and then turn on the panel PC. 4. Refer to the manual(s) which accompanied your serial device(s) fo. instructions on configuring your operating environment to recogniz. the device(s). 5. Run the BIOS setup program and configure the jumper settings t. change the mode of the COM ports. (See Section 5.3.. Chapter 3 Using the Panel PC 3.. VGA Por. An external VGA-compatible device may be connected to the syste. through the 15-pin external port located on the rear of the system unit. Th. panel PC simultaneously supports an external CRT monitor in addition t. its own LCD display. 1. Be sure the panel PC is turned off. 2. Connect the external monitor to the system. (See Fig. 3-5.. 3. Turn on the panel PC and the external monitor. 3.1. Game Por. An external game device may be connected to the system through th. 15-pin external port located on the rear of the system unit. 1. Be sure the panel PC is turned off. 2. Connect the external joystick or game device to the system. (See Fig. 3-5.. 3. Turn on the panel PC and the external joystick or game device (i. applicable). 4. Install the driver before you use the joystick or game device. 3.1. USB Port. An external USB device may be connected to the system through the 4-pi. USB ports located on the rear side of the system unit. 1. Connect the external device to the s...