Stimmen - 5, Durchschnittliche Bewertung: 4.2
(
)
)
|
Anleitung Zusammenfassung
Refer to the NetLinx Master instruction manual for more detailed information on the use of the new Web-based NetLinx Security. 1. Press and hold the two lower buttons on both sides of the display for 3 seconds to open the Setup page. 2. Press the Protected Setup button (located on the lower-left of the panel page) to open the Protected Setup page and display an on-screen keypad. 3. Enter the appropriate password into the Keypad’s password field (1988 is the default password with a new unit) and press Done. 4. Press the G4 WebControl button to open the G4 Web Control page (FIG. 43). FIG. 43 G4 Web Control page 5. Press the Enable/Enabled button until it toggles to Enabled and turns light blue. 6. The Network Interface Select field is read-only and displays the method of communication to the web. • Wireless is used when a wireless card is detected within the internal card slot. This method provides an indirect communication to the web via a pre-configured Wireless Access Point. The Network Interface Select field is read-only and defaulted to Wireless, since the device has no Ethernet cable connection. 7. Press the Web Control Name field to open the Web Name keyboard. MVP-5200i Modero Viewpoint Widescreen Touch Panel 45J Configuring Communication NOTE 8. From the Web Name keyboard, enter a unique alpha-numeric string to identify this panel. This information is used by the NetLinx Security Web Server to display on-screen links to the panel. The on-screen links use the IP Address of the panel and not the name for communication (FIG. 44). FIG. 44 Sample relationship between G4 Web Control and Mange WebControl Connections window 9. Assign the alpha-numeric string for the Web Control name and then press Done. 10. Press the Web Control Password field to open the Web Password keyboard. 11. From the Web Password keyboard, enter a unique alpha-numeric string to be assigned as the G4 Authentication session password associated with VNC web access of this panel. 12. Press Done after assigning the alpha-numeric string for the Web Control password. 13. Press the Web Control Port field to open the Web Port Number keypad. 14. Within the keypad, enter a unique numeric value to be assigned to the port on which the VNC Web Server is running. The default value is 5900. Press Done after entering the value. The remaining fields within the G4 Web Control Settings section of this page are read-only and cannot be altered. 15. Press the Up/Down arrows on either sides of the G4 Web Control Timeout field to increase or decrease the amount of time the device can remain idle with no cursor movements before the session is closed and the user is disconnected. 16. Press the Back button to open the Protected Setup page. 17. Press the on-screen Reboot button to save any changes and restart the device. Verify that the NetLinx Master’s IP Address and System Number have been properly entered into the Master Connection section of the System Settings page. L46 MVP-5200i Modero Viewpoint Widescreen Touch Panel Configuring Communication NOTE Using the NetLinx Master to control the G4 panel Refer to the particular NetLinx Master’s instruction manual for detailed information on how to download the latest firmware from This firmware build enables SSL certificate identification and encryption, HTTPS communication, ICSP data encryption, and disables the ability to alter the Master security properties via a TELNET session. In order to make full use of the SSL encryption, the web browser used should incorporate an encryption feature. This encryption level is displayed as a Cipher strength. Once the Master’s IP Address has been set through NetLinx Studio version 2.x or higher: 1. Launch your web browser. 2. Enter the IP Address of the target Master (example: into the web browser’s Address field. 3. Press the Enter key on your keyboard to begin the communication process between the target Master and your computer. • Initially, the Master Security option is disabled from within the System Security page, and no username and password is required for access or configuration. • Both HTTP and HTTPS Ports are enabled by default via the Manage System > Server page. • If the Master has been previously configured for secured communication, click OK to accept the AMX SSL certificate, if SSL is enabled, and then enter a valid username and password into the fields within the Login dialog. 4. Click OK to enter the information and proceed to the Master’s Manage WebControl Connections window. This page (FIG. 45) is accessed by clicking on the Manage connections link (within the Web Control section within the Navigation frame). Once activated, this page displays links to G4 panels running the latest G4 Web Control feature that were previously set up and activated on the device. G4 panels ■ Compatble devices field (showing G4 WebControl links) Compression Options FIG. 45 Manage WebControl Connecti...