Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
range : 01H to 63H. by setting '0', server can control all products. * In case of operating with more than 2 sets using set ID as '0' at the same time, it should not be checked the ack message. Because all sets will send the ack message, so it's impossible the check the whole ack messages. * [DATA]: To transmit command data. Transmit 'FF' data to read status of command. * [Cr]: Carriage Return (ASCII code '0 x 0 D') * [ ]: ASCII code Space (0 x 20) OK Acknowledgement [Command2][ ][Set ID][ ][OK][Data][x] * The Product transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer. * Note : In this mode, display will send the acknowledgement after power on processing completion. There might be a time delay between command and acknowledgement. * No acknowledgement signal will be sent from display, if Set ID in transmission signal is set to ‘00’(=0x00). Error Acknowledgement [Command2][ ][Set ID][ ][NG][Data][x] * If there is error, it returns NG * Real data mapping Hexadecimal Num. (Setting Value) Decimal Num. (Real Value) 0 0 A 10 F 15 10 16 20 32 64 100 FE 254 FF 255 03. Screen Mute(Command: k, d) To select screen mute on / off. Transmission [k][d][ ][Set ID][ ][Data][Cr] Data 00: Screen on 01: Screen off Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x] 01. Power(Command: k, a) To control Power On/Off of the set. Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 00: Power Off 01: Power On Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x] * The normal acknowledgement signal returns after the power of the set is turned on completely. * There might be a time delay between the transmission and acknowledgement signals. 04. Volume Mute(Command: k, e) To control On/Off of the Volume Mute. Transmission [k][e][ ][Set ID][ ][Data][Cr] Data 00: Volume Mute On (Volume Off) 01: Volume Mute Off (Volume On) Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x] 02. Aspect Ratio(Command: k, c) To adjust the screen format. You can also adjust the screen format using the ARC(Aspect Ratio Control) button on remote control or in the Screen menu. Transmission [k][c][ ][Set ID][ ][Data][Cr] Data 01: Normal Screen(4:3) 02: Wide Scran(16:9) 04: Zoom(AV, Component, HDMI/ Display Port DTV) 06: Original 09: Just Scan(HDMI1/ HDMI2/ DVI/ Display Port -DTV) * Available only with 720p or higher. 10 to 1F: Cinema Zoom 1 to 16(AV, HDMI1/HDMI2/ DVI/Display Port -DTV) Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x] 05. Volume Control(Command: k, f) To adjust Volume. Transmission [k][f][ ][Set ID][ ][Data][Cr] Data Min. 00H to Max. 64H : 0~100 * Refer to 'Real data mapping’. Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x] 06. Contrast(Command: k, g) To adjust screen contrast. You can also adjust the contrast in the Picture menu. Transmission [k][g][ ][Set ID][ ][Data][Cr] Data Min. 00H to Max. 64H : 0~100 * Refer to 'Real data mapping’. Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x] 09. Tint(Command: k, j) To adjust the screen tint. You can also adjust the tint in the Picture menu. Transmission [k][j][ ][Set ID][ ][Data][Cr] Data Min. 00H to Max. 64H 00H: Step R50 64H: Step G50 * Refer to 'Real data mapping’. Acknowledgement [j][ ][Set ID][ ][OK/NG][Data][x] 07. Brightness(Command: k, h) To adjust screen brightness. You can also adjust the brightness in the Picture menu. Transmission [k][h][ ][Set ID][ ][Data][Cr] Data Min. 00H to Max. 64H : 0~100 * Refer to 'Real data mapping’. Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x] 10. Sharpness(Command: k, k) To adjust the screen Sharpness. You can also adjust the sharpness in the Picture menu. Transmission [k][k][ ][Set ID][ ][Data][Cr] Data Min. 00H to Max. 32H : 0~50 * Refer to 'Real data mapping’. Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x] 08. Color(Command: k, i) To adjust the screen color. You can also adjust the color in the Picture menu. Transmission [k][i][ ][Set ID][ ][Data][Cr] Data Min. 00H to Max. 64H : 0~100 * Refer to 'Real data mapping’. Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x] 11. OSD Select(Command: k, l) To control OSD on/off to the set. Transmission [k][l][ ][Set ID][ ][Data][Cr] Data 00: OSD Off 01: OSD On Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x] 12. Remote Lock /Key Lock(Command: k, m) To control Remote Lock on/off to the set. This function, when controlling RS-232C, locks the remote control and the local keys. Transmission [k][m][ ][Set ID][ ][Data][Cr] Data 00: Off 01: On Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x] 15. White Balance Red Gain(Command: j, m) To adjust white balance red gain. Transmission [j][m][ ][Set ID][ ][Data][Cr] Data 00~FE: Red gain 0~254 Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x] 13. Balance(Command: k, t) To adjust the sound balance. Transmission [k][t][ ][Set ID][ ][Data][Cr] Data Min. 00H to Max. 64H 00H: Step L50 64H: Step R50 * Refer to 'Rea...