Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Connect the external device and the Monitor with the 15 pin signal to RCA cable as shown on the following illustration. To display images by using progressive scan, make sure to use the component cable. Connecting to a HD receiver, DVD, Camcorder, Camera, Gaming Device or VCR player Connect a HD receiver, DVD, or VCR player to the Monitor and select an appropriate input mode. HDMI connection Transmits the digital video and audio signals from an external device to the Monitor. Connect the external device and the Monitor with the HDMI cable as shown on the following illustration. VIDEO AUDIO OUT (not included) HDMI (not included) (not included) NOTE yyUse a High Speed HDMI™ Cable. yyHigh Speed HDMI™ Cables are tested to carry an HD signal up to 1080p and higher. Connecting to a USB Connect a USB storage device such as s USB flash memory, external hard drive, MP3 player or a USB memory card reader to the Monitor and access the USB menu to use various multimedia files. AV(CVBS) connection Transmits the analog video and audio signals from an external device to the Monitor. Connect the external device and the Monitor with the 15 pin signal to RCA cable as shown on the following illustration. A U D I O O U T V I D E O O U T or (not included) (not included) Connecting to the LAN NOTE yyUsing LAN establishes communication between your PC and the monitor and enables to use the OSD menus on the PC as well as on the monitor. LAN connection A Connect PC to Monitor directly. LAN Network Network Monitor PC Network B Using a router(Switch) LAN Switch PC Monitor C Using the Internet. LAN Monitor PC Daisy Chain Monitors Use this function to share the RGB video signal with other monitors without having to use a separate signal splitter box. To use different products connected to each other Connect one end of the signal input cable (15-pin D-Sub Signal Cable) to the RGB OUT connector of product 1 and connect the other end to the RGB IN connector of other products Monitor 3 Monitor 4 Monitor 1 Monitor 2 RGB OUT (PC) VIDEO A U D I O O U T V I D E O O U T 15-pin D-Sub Signal Cable (Max 3m) Component Mode AV(CVBS) Mode RGB Mode NOTE yyThe number of monitors that can be connected to one output may vary depending on signal status and cable loss. If the signal status is good, and there is no cable loss, it is possible to connect up to 9 monitors. If you want to connect more than this number of monitors, it is recommended to use a distributor. yyWhen multi-connecting in/out cascade format, no loss cables are recommended. 56 TROUBLESHOOTING ENG ENGLISH TROUBLESHOOTING No image is displayed Problem Resolution Is the product power cord connected? y y See if the power cord is properly connected to the outlet. Is the power indicator light on? y y See if the power switch is turned on. y y May need service. Power is on, power indicator is blue but the screen appears extremely dark. y y Adjust brightness and contrast again. y y Backlight may need repair. The power indicator amber? y y If the product is in power saving mode, move the mouse or press any key. y y Turn both devices off and then back on. Does the 'Out of range' message appear? y y The signal from the PC (video card) is out of the vertical or horizontal frequency range of the product. Adjust the frequency range by referring to the Specifications in this manual. * Maximum resolution RGB, HDMI, DVI-D, Display Port : 1920 x 1080 @ 60 Hz Does the 'Check signal cable' message appear? y y The signal cable between PC and product is not connected. Check the signal cable. y y Press the 'INPUT' menu in the remote Control to check the input signal. 'Unknown Product' message appears when the product is connected. Problem Resolution Did you install the driver? y y Install the product driver, which is provided with the product, or download it from the web site. (y y See if the plug&play function is supported by referring to the video card user manual. TROUBLESHOOTING 57 ENG ENGLISH 'Key Lock On' message appears. Problem Resolution The 'Key Lock On' message appears when pressing the Menu button. The Lock function prevents the OSD settings from being changed inadvertently. To release the lock, go to Menu and Option and disable the Key Lock option. The screen image looks abnormal. Problem Resolution Is the screen position wrong? y y D-Sub analog signal - Press the "AUTO" button in the remote control to automatically select the optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Position OSD menu. y y See if the video card resolution and frequency are supported by the product. If the frequency is out of range, set to the recommended resolution in the Control Panel "Display" Setting menu. Do thin lines appear on the background screen? y y D-Sub analog signal - Press the "AUTO" button in the remote control to automatically select an optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Clock OS...