The login page and the OSD's password protection can be enabled in the PCoIP management console. yyGateway The Gateway field contains the gateway IP address of the device. If DHCP is disabled, this field is required. If DHCP is enabled, this field cannot be edited. yyPrimary DNS Server The Primary DNS Server field contains the primary DNS IP address of the device. This field is optional. If DHCP is enabled, this field cannot be edited. yySecondary DNS Server The Secondary DNS Server field contains the secondary DNS IP address of the device. This field is optional. If the DHCP is enabled, this field cannot be edited. yyDomain Name The Domain Name field contains the domain name used, e.g. "domain local". This field is optional. It specifies on which domain the host or portal operates. yyFQDN The FQDN field represents the Fully Qualified Domain Name of the host or portal. The default value is PCoIP-host-MAC or PCoIP-portal-MAC, where MAC is the MAC address of the host or portal. If there is a domain name, it will be added to the FQDN in the format of PCoIP-host-MAC.domain.local Network Tab The Network tab allows the administrator to configure the portal network parameters. NOTE yyThe network parameters can also be configured using the Webpage Administration Interface. Figure 2-7. Network Configuration yyEnable DHCP If the Enable DHCP option is selected, a device will be connected to the DHCP server. that allocates the IP address, subnet mask, gateway IP address, and DNS server. If this option is disabled, the above parameters must be configured manually. yyIP Address The IP Address field contains the IP address of the device. If DHCP is disabled, this field is required. If DHCP is enabled, this field cannot be edited. This field must contain the correct IP address. If an incorrect IP address is provided, an OSD message is displayed prompting the administrator to provide the correct the IP address. yySubnet Mask The Subnet Mask field contains the subnet mask of the device. If DHCP is disabled, this field is required. If DHCP is enabled, this field cannot be edited. This field must have the correct subnet mask. If an incorrect subnet mask is provided, an OSD message is displayed prompting the administrator to provide the correct the subnet mask. NOTE yyIn order to utilize the FQDN feature, a DNS server, configured properly with DHCP option 81, must be used. yyEthernet Mode The Ethernet Mode field specifies the portal's Ethernet mode. The available options are as follows. yyAuto yy100 Mbps Full-Duplex yy10 Mbps Full-Duplex If another network device (for example, a switch) is configured to operate under 10 Mbps Full-Duplex, 100Mbps Full-Duplex or 1GbpsFull-Duplex, the administrator should always set the Ethernet Mode field to Auto; and if the device is to operate under only one speed out of multiple settings, select ei- ther 10 Mbps Full-Duplex or 100 Mbps Full-Duplex. Tab The IPv6 tab is used when the portal is connected to the network configured with the IP v6. yySecondary DNS Server The Secondary DNS Server field contains the sec- ondary DNS IP address of the device. This field is optional. If DHCPv6 is enabled, this field cannot beedited. yyDomain Name The Domain Name field contains the domain name used, e.g. "domain local". This field is optional. It specifies on which domain the host or portal oper- ates. yyFQDN The FQDN field represents the Fully Qualified Do- main Name of the host or portal. The default value is PCoIP-host-MAC or PCoIP-portal-MAC, where MAC is the MAC address of the host or portal. If there is a domain name, it will be added to the FQDN in the format of PCoIP-host-MAC.domain. local. yyEnable SLAAC Select the Enable SLAAC field to use the stateless auto-configuration of the device. yyEnable Manual Address Select the Enable Manual Address field to enter the device address manually. yyManual Address In the Manual Address field, enter the IP address manually. yyEnable IPv6 If you select Enable IPv6, the portal in use can be connected to the network configured with the IPv6. yyLink Local Address The Link Local Address field is automatically filled with the IP address of a device. yyGateway The Gateway field contains the gateway IP ad- dress of the device. Enter the gateway address to be used by a device. yyEnable DHCPv6 To assign the Dynamic Host Configuration Protocol version 6 (DHCPv6) of a device select the Enable DHCPv6 field. yyDHCPv6 Addresses When DHCPv6 is enabled and the device restarts, the server enters the device addresses automati- cally. yyPrimary DNS Server The Primary DNS Server field contains the pri- mary DNS IP address of the device. This field is optional. If DHCPv6 is enabled, this field cannot be edited. Discovery Tab The Discovery tab allows the administrator to easily find a portal in the PCoIP system. Label Tab The Label tab allows the administrator or host to add customized information to the portal...
Hersteller: LG
