Stimmen - 0, Durchschnittliche Bewertung: 0 ( )

Hersteller: Philips Dateigröße: 11 mb Dateiname: Unterrichtssprache:

l Make sure the computer is turned on. Screen says l Make sure the vertical sync of input signal is within the range of 56 ~ 76 Hz. l Change the refresh rate to 56~76Hz within 10 minutes. l Re-power on monitor to start over again if you failed to change the refresh rate within 10 minutes. AUTO button not working properly l The Auto Function is designed for use on standard Macintosh or IBMcompatible PCs running Microsoft Windows. l It may not work properly if using nonstandard PC or video card. l The AUTO adjustment does not function when digital input is used for display. Imaging Problems Display position is incorrect l Press the Auto button. l Adjust the image position using the Horizontal Position and/or Vertical Position in OSD Main Controls. Image vibrates on the screen l Check that the signal cable is properly connected to the graphics board or PC. Vertical flicker appears l Press the Auto button. l Eliminate the vertical bars using the Phase/Clock of More Settings in OSD Main Controls. Horizontal flicker appears l Press the Auto button. l Eliminate the vertical bars using the Phase/Clock of More Settings in OSD Main Controls. The screen is too bright or too dark l Adjust the contrast and brightness on OSD Main Controls. (The backlight of the LCD monitor has a fixed life span. When the screen becomes dark or begins to flicker, please contact your dealer). An after-image appears l If an image remains on the screen for an extended period of time, it may be imprinted in the screen and leave an after-image. This usually disappears after a few hours An after-image remains after the power has been turned off. l This is characteristic of liquid crystal and is not caused by a malfunction or deterioration of the liquid crystal. The after-image will disappear after a peroid of time. Green, red, blue, dark, and white dots remains l The remaining dots are normal characteristic of the liquid crystal used in today’s technology. For further assistance, refer to the Consumer Information Centers list and contact your local Philips distributor. RETURN TO TOP OF THE PAGE • CE Declaration of Conformity • Energy Star Declaration •Federal Communications Commission (FCC) Notice (U. S. Only) •FCC Declaration of Conformity •Commission Federale de la Communication (FCC Declaration) •EN 55022 Compliance (Czech Republic Only) •VCCI Class 2 Notice (Japan Only) •MIC Notice (South Korea Only) •Polish Center for Testing and Certification Notice •North Europe (Nordic Countries) Information •BSMI Notice (Taiwan Only) •Ergonomie Hinweis (nur Deutschland) •Philips End-of- Life Disposal • Information for UK only • Waste Electrical and Electronic Equipment- WEEE •China RoHS •Troubleshooting • Other Related Information Regulatory Information CE Declaration of Conformity Philips Consumer Electronics declare under our responsibility that the product is in conformity with the following standards - EN60950-1:2001 (Safety requirement of Information Technology Equipment) - EN55022:1998 (Radio Disturbance requirement of Information Technology Equipment) - EN55024:1998 (Immunity requirement of Information Technology Equipment) - EN61000-3-2:2000 (Limits for Harmonic Current Emission) - EN61000-3-3:1995 (Limitation of Voltage Fluctuation and Flicker) following provisions of directives applicable - 73/23/EEC (Low Voltage Directive) - 89/336/EEC (EMC Directive) - 93/68/EEC (Amendment of EMC and Low Voltage Directive) and is produced by a manufacturing organization on ISO9000 level. The product also comply with the following standards - ISO9241-3, ISO9241-7, ISO9241-8 (Ergonomic requirement for CRT Monitor) - ISO13406-2 (Ergonomic requirement for Flat Panel Display) - GS EK1-2000 (GS specification) - prEN50279:1998 (Low Frequency Electric and Magnetic fields for Visual Display) - MPR-II (MPR:1990:8/1990:10 Low Frequency Electric and Magnetic fields) - TCO'99, TCO'03 (Requirement for Environment Labelling of Ergonomics, Energy, Ecology and Emission, TCO: Swedish Confederation of Professional Employees) for TCO versions RETURN TO TOP OF THE PAGE Energy Star Declaration This monitor is equipped with a function for saving energy which supports the VESA Display Power Management Signaling (DPMS) standard. This means that the monitor must be connected to a computer which supports VESA DPMS. Time settings are adjusted from the system unit by software. NUTEK VESA State LED Indicator Power Consumption Normal operation ON (Active) Green < 47W (TYP) Power Saving Alternative 2 One step OFF (Sleep) Amber < 1 W Switch Off OFF < 1 W Declaration of Conformity for Products Marked with FCC Logo, United States Only This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RETURN TO TOP OF THE PAGE Commission Federale de la Communication (FCC Declaration) Cet...

Herunterladen

Geben Sie zwei Ziffern: