Stimmen - 0, Durchschnittliche Bewertung: 0 ( )

Hersteller: Philips Dateigröße: 5.92 mb Dateiname: Unterrichtssprache:

4.2.4. PIP menu PIPPIP inputPIP changePIP sizePIP resetPictureScreenAudioPIPConfiguration1Configuration2Advanced optionPIP audio PIP Select the PIP (Picture-in-Picture) mode. The options are: {Off} / {PIP} / {POP} / {PBP aspect} / {PBP full}. PIP input Select the input signal for the sub-picture. PIP change Enlarges the smaller picture to become the main picture, and vice versa. PIP size Select the size of the sub picture in the PIP (Picture-in-Picture) mode. The options are: {Small} / {Medium} / {Large}. PIP audio Select the audio source in the PIP (Picture-in-Picture) mode. • {Main} - Select audio from the main picture • {Sub} - Select audio from the sub picture. PIP reset Reset all settings in the PIP menu to factory preset values. NOTES: • The PIP function is available only for certain signal source combinations as shown in the table below. • The availability of the PIP function will also depend on the resolution of the input signal being used. Main Picture Sub Picture DVI VGA HDMI YPbPr S-Video Video Card OPS DVI X X X X O O X VGA X X X X O O X HDMI X X X X O O X YPbPr X X X X O O X S-Video O O O O X X O Video O O O O X X O Card OPS X X X X O O X (O: PIP function available, X: PIP function unavailable) By pressing the [PIP ON/OFF] button on the remote control, you can change the mode in the order shown below: PIPPOPPBP aspectPBP fullOff The resolutions in the PIP and POP modes are configured as follows: PIP SIZE {Small} : 320 x 240 pixels {Medium} : 480 x 320 pixels {Large} : 640 x 480 pixels POP SIZE : 474 x 355 pixels NOTE: The images displayed in the sub picture always fit the PIP sizes shown above irrespective of the aspect ratio of the input image. 4.2.5. Configuration1 menu Switch on stateAuto adjustPower saveLanguageColor systemPictureScreenAudioPIPConfiguration1Configuration2Advanced optionPanel savingNetwork control portNetwork settingsConfiguration resetFactory reset Switch on state Select the display status used for the next powering on. • {Power off} - The display will remain off when the power cord is connected to a wall outlet. • {Forced on} - The display will turn on when the power cord is connected to a wall outlet. • {Last status} - The display will return to the previous power status (on/off/standby) when removing and replacing the power cord. Auto adjust Use this function to let the display automatically optimize the display of VGA input image. NOTE: This item is functional for VGA input only. Power save Set the display to reduce the power automatically. • {RGB} - Select {On} to let the display enter DPMS mode when no signal detected from the HDMI Graphic mode, HDMI, DVI-D, or VGA inputs after three successive cycles. • {VIDEO} - Select {On} to let the display enter power saving mode when no signal detected from the HDMI Video mode or YPbPr inputs after three successive cycles. Language Select the language used in the OSD menu. The options are: {} / {} / {} / {} / {} / {} / {} / {} / {}. Panel saving Choose to enable the panel saving functions to reduce the risk of the “image persistence”. • {Cooling Fan} - Select {On} to turn on the cooling fan all the time. Select {Auto} to turn on/off the cooling fan according to the display’s temperature. NOTES: • The default {Auto} option will start running the cooling fan if the temperature of 65°C (152°F) is reached, and will keep running for 30 minutes after cooling down to the temperature of 62°C (144°F). • A temperature-warning message will be shown on the screen once the temperature reaches 79°C (174°F). All key function except [Power] key will then be disabled. • {Brightness} - Select {On} and the brightness of the image will be reduced to an appropriate level, and the Brightness setting in the Picture menu will become unavailable. • {Pixel shift} - Select the time interval ({Auto} / {10 ~ 900} Seconds / {Off}) for the display to slightly expand the image size and shift the position of pixels in four directions (up, down, left, or right). NOTE: The default {Auto} setting for menu item Pixel shift does not support menu items Zoom mode, H/V Position, and PIP. Color system Selects the Color System depends on your input video format. The options are: {Auto} / {NTSC} / {PAL} / {SECAM} / {4.43NTSC} / {PAL-60}. NOTE: This item is functional for S-VIDEO or VIDEO input only. Network control port Select the nectwork control port. The options are: {RS232} / {LAN(RJ45)}. NOTE: If {LAN(RJ45)} is selected, then {RS232} will not be activated, even if a cable is attached, and vice versa. Network settings Assign {IP address}, {Subnet Mask}, and {Default gateway} for the display. Network settingsNetwork host nameDHCPIP addressSubnet maskDefault gatewayLogin user nameLogin password9172255000- - - admin0[ SET ] change [SET] in STOREZDisable1625500L- - - 0000100- - - • DHCP - Choose to enable or disable the DHCP function. If enabled, the display will be assigned IP address, Subnet mask and Default gateway automatically. If disabled, you will be prompted to en...

Herunterladen

Geben Sie zwei Ziffern: