Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
By using the USB, you will be able to connect your mouse, keyboard, and other peripherals to your display instead of having to connect them to your computer. This will give you greater flexibility in setting up your system. USB allows you to connect a chain of up to 120 devices on a single USB port; and you can “hot” plug (attach them while the computer is running) or unplug them while maintaining the Plug and the Plug auto detection and configuration. This display has an integrated BUS- powered USB hub, allowing up to 2 other USB devices to be attached it. 1. Connect the upstream port of the display to the downstream port of the USB compliant PC or another hub using the USB cable. (Computer must have a USB port) 2. Connect the USB compliant peripherals to the downstream ports of the display. USB downstream Port x (4) Connect the cables from USB compliant peripherals-such as mouse, memory stick or USB hard disk, etc. USB upstream Port x (1) Connect to downstream connectors of desktop or laptop computers. (However, the computer must support USB and have the USB port.) 3. The monitor’s USB terminal supports USB 2.0 and High Speed cables. High Speed Full Speed Low Speed Data Rate 480Mbps 12Mbps 1.5Mbps Power 2.5W 2.5W 2.5W Consumption (Max,each Port) (Max,each Port) (Max,each Port) A7 NOTE To activate the USB hub function, the display must be connected to a USB compliant PC(OS) or another hub with the USB cable(enclosed). When connecting the USB cable, check that the shape of the connector at the cable side matches the shape at the connecting side. Even if the display is in a power saving mode, USB compliant devices will function when they are connected the USB ports(both the upstream and downstream) of the display. Connecting the Display To arrange the cables Connect the power cord and the signal cable as shown in the figure and then fix them to the cable holders 1 and 2. 1. Please insert the cable holder1 2. Please put the power cord and into a hole. the signal cable in the cable holder 1. Cable Holder 1 3. Please put the power cord and the signal cable in the cable holder 2. While pressing the bottom of cable holder 2 with one hand, pull the top of it with the other hand as shown in the picture. Press Pull Cable Holder 2 A8 Control Panel Functions Front Panel Controls 4 5 Power Button Touching the button to turn the power on and touch the button again to turn it off. Power Indicator This Indicator lights up blue when the display operates normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to amber. You can adjust monitor brightness to be lighter ( ) Buttons or darker ( ). When adjusting brightness, it will beep once when you reach the maximum or minimum level. You can turn DFC function on or off by pressing two buttons at the same time for longer than three seconds. When DFC is turned on, the power indicator (blue light) flickers once after the beep. When DFC is turned off, the indicator flickers three times after the beep. When DFC is on, if the / buttons are not pressed at the same time, the brightness control function might be turned on. *What is DFC (Digital Fine Contrast) Function? After analyzing input signals, this product makes dark areas on the screen darker, providing greater contrast ratio to viewers. Buttons You can turn on or off the alarm ringing when adjusting buttons while the power is on. Touch any button to check if the sound is on or off. If sound is heard, it means the sound is on. If not, it means the sound is off. Buttons You can turn Power Indicator on or off by touching the button lightly while the power is on. A9 Troubleshooting Check the following before calling for service. No image appears Is the power cord of the • Check and see if the power cord is connected properly to the power outlet. display connected? • Adjust the brightness and the contrast. Is the power on and the power indicator blue or green? Is the power indicator • If the display is in power saving mode, try moving amber? the mouse or pressing any key on the keyboard to bring up the screen. • Try to turn on the PC. Important Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution. Reasons for Recommending Optimal Resolution : The aspect ratio is 16:10. If the input resolution is not 16:10 (for instance, 16:9, 5:4, 4:3), you might encounter problems such as blurred letters, blurry screen, cut-off screen display or tilted screen. The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. In this case, please ask to the computer or the video card manufacturer. A10 Troubleshooting Display image is incorrect The screen color is mono or abnormal. The screen blinks. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the ...
Dieses Handbuch ist für folgende Modelle:Monitore - W3000H-BNS (534.77 kb)