Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories. r/j\ CAUTION- • Do not use any unapproved accessories to ensure the safety and product life span. • Any damages or injuries by using unapproved accessories are not covered by the warranty. Q NOTE- • The accessories supplied with your product may vary depending on the model. • Product specifications or contents in this manual may be changed without prior notice due to upgrade of product functions. • User should use shielded signal interface cables (D-SUB cable / DVI-D cable) with ferrite cores to maintain standard compliance for the product. ENGLISH ENGLISH 4 ASSEMBLING AND PREPARING Connection panel (See p.10) ASSEMBLING AND PREPARING 5 Button Description MENU Accesses the main menus.(See p.13) OSD LOCKED/ UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. MODE Use this button to enter USER, MOVIE,TEXT,PHOTO,sRGB menus.(See p.18) DUAL Use this button to enter DUAL MONITOR and DUAL WEB menus.(See p.19) AUTO When adjusting your display settings, always press the AUTO button on the MONITOR SETUP OSD. (Only supported in Analog Mode) The best display mode 1920x 1080 INPUT You can choose the input signal. • When two input signals are connected, you can select the input signal (D-SUB/DVI/ HDMI) you want. • When only one signal is connected, it is automatically detected. The default setting is D-SUB. EXIT Exit the OSD(On Screen Display). (!) (Power Button) Turns the power on or off. Power Indicator The power indicator stays blue if the display is running properly (On Mode). If the display is in Sleep Mode, the power indicator blinks blue. ENGLISH ENGLISH 6 ASSEMBLING AND PREPARING Setting up the Monitor set Attaching the Stand Base 1 Place the Monitor set with the screen side down on a flat and cushioned surface. r/j\ CAUTION- Lay a foam mat or soft protective cloth on the surface to protect the screen from damage. 2 Attach the Stand Base and then tighten the screw to the right with a Coin. Detaching the Stand Base 1 Place the Monitor set with the screen side down on a flat and cushioned surface. 2 Turn the screw to the left, and then pull out the Stand Base from the Stand Body. r/j\ CAUTION- • This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. • Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. ASSEMBLING AND PREPARING 7 Mounting on a table 1 Lift and tilt the Monitor set into its upright position on a table. Leave a 10 cm (minimum) space from the wall for proper ventilation. 2 Connect the Power Cord to a wall outlet. 3 Press (i)(Power) button on the front switch panel to turn the power on. WARNING- When you adjust the angle, do not hold the bottom of the Monitor set frame as shown on the following illustration, as may injure your fingers. Do not touch or press the screen when adjusting the angle of the monitor. r® NOTE- Tilt from +15 to -5 degrees up or down to adjust the angle of the Monitor set to suit your view. - 5° 15° Front Rear r/j\ CAUTION- Unplug the power cord before moving the Monitor to another location. Otherwise electric shock may occur. ENGLISH ENGLISH 8 ASSEMBLING AND PREPARING Using the Kensington security system The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit Connect the Kensington security system cable between the Monitor set and a table. r © NOTE- The Kensington security system is optional. You can obtain it from most electronics stores. Mounting on a wall For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide. When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop. Please use VESA standard as below. • 784.8 mm (30.9 inch) and under * Wall Mount Pad Thickness : 2.6 mm * Screw : O 4.0 mm x Pitch 0.7 mm x Length 10 mm • 787.4 mm (31.0 inch) and above * Please use VESA standard wall mount pad and screws. ASSEMBLING AND PREPARING 9 Model |IPS225V/IPS235V| VESA (A x B) 100 x100 Standard screw M4 Number of screws 4 r/j\ CAUTION- • Disconnect the power cord first, and then move or install the Monitor set. ...
Dieses Handbuch ist für folgende Modelle:Monitore - IPS225V-BN (2.42 mb)