Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
Press the front {2} key to select, the User Color adjustment screen. User Color adjustment R100 G 80 I I B 60 Note: Record the initial values of R, G and B here before making any adjustments: R ( Red) _ G ( Green ) _ B ( Blue ) _ The white in the video image can be adjusted to the user’s preferred color. 1) Use the (Tj key to select R (red) or G (green) or B (blue). 2) Use the 3 or B keys to adjust the color as desired. * Recall of the user’s color is not possible, so make a note of the initial setting before adjusting. -11 - < On-Screen Display» < Function and Operation» Recall OK ? □3: Yes NO :[5) To return to the initial settings (the settings at the time of factory shipment). 1) When the 0 key (Yes) is pressed, the settings are recalled and the menu screen returns. (Recall = return to settings at time of factory shipment.) 2) When the 0 key (No) is pressed, the menu screen returns without the settings being recalled (the settings return to what they were immediately before the recall). * If no operations are performed for about 30 seconds, the screen goes off without recall. 5© Video Level Video Level 0.7V 0.7/1 V : [5] The video input signal level can be matched to the computer being used. Either 0.7V or 1.0V can be selected with the [2] key. Note : 0.7V is typical. (If wrong level is selected image may be too dim or too bright.) ?£ Language selection Language fra rana esp The language used by the On-Screen Display can be selected with the “H” and “B" keys from among French, English, and Spanish. FRA: French ENG: English ESP: Spanish ill OSD Position It is possible to adjust the position that the On-Screen Display is to be shown in. The On-Screen Display will rotate in a counterclockwise direction every time the [D key is pressed. Jp| DegaUSS (Demagnetise(See Trouble Shooting Page 17 Third Symptom.)) Degaussing operation can be selected. Use this control if display color is abnormal. After this is selected, the degaussing action takes place for approximately 6 seconds. Key operation is not possible while demagnetization is performed. Fvl Signal 1024 x 768 fH 60.2kHz fV 74.8 Hz Resolution (1024 x 768) will only appear if the video signal is a preset or reservation timing (See page 15). Signal displays the computer’s approximate horizontal sync frequency (fH) and vertical sync frequency (fV). If the fH or fV are outside the specified range then the Monitor Self Test function will automatically display the Signal Error menu (See page 9, Monitor Self Test, 2). -12 - Power Management System This monitor conforms to the VESA DPMS standard. If the Power stand-by switch is ON. This function can reduce power consumption of the display unit. The computer and video board being used must also conform to the VESA DPMS standard. * Consult the Operation Manuals for the hardware being used. Modes change in response to input signals as indicated in the table below. APM State Screen status Power Indicator color Power consumption Return time Input signals video horizontal sync. vertical sync. ON STATE with display green normal — ON ON ON STAND-BY without display yellow < 15 watts < 4 sec. OFF OFF ON SUSPEND without display yellow < 15 watts < 4 sec. OFF ON OFF OFF STATE without display yellow < 8 watts < 20 sec. OFF OFF OFF Caution How to release the system from the power management function. 1) Read the Operation Manuals for the hardware you are using. 2) Press one of the [Q • g • B * 0 keys on the front panel. The No Signal screen appears, and the monitor side power management function is released (only in OFF STATE). Memories This display has two types of memory to store the data sets that controls the on-screen image. The first type of memory is the Preset Memory which is set by the factory. The second type is the User Memory which is set by the user. Both memories store the Horizontal Size, Vertical Size, Horizontal Position, Vertical Position, Vertical Pincushion, Side Pincushion Balance, Trapezoid and Parallelogram adjustments of the displayed image. Preset Memory There are 1 preset (7 reservation) timings that are set by the factory. The preset timing will automatically size and center the image with video boards which use these timings. Please see page 14 for Timing Specifications. User Memory • There are 13 memory locations that allow for user timing. The image size, position, geometric distortion are adjusted by the user. Please see page 15 and 16 for recommended timings that the display supports. • If the User Memory is completely full, and a new set of data is saved, the oldest data set in the User Memory will be deleted. • The User Memory has priority over the Preset Memory. • When the user timing is input, the Vertical, Horizontal frequencies and sync polarities of the signal are compared with the previous data stored in memory. The input signal will be stored as a new data set if one of its parameters is different from the pre...