Stimmen - 4, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
AOC 9KLR v3_123102 6 Before You Operate the Monitor AOC 9KLR Connecting the Wires Using An Optional Power Cord (Not Supplied) The power cord supplied with your monitor can only be connected to a grounded electrical wall socket or power strip. If you wish to connect your monitor to a power supply using the power input socket on the back of your computer, you must purchase a power cord with CEE-22 terminated connectors (see illustration above). Follow these steps: 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. 2. Connect the power cord into your monitor's power input socket. 3. Plug the other end of the power cord into the power output socket on your PC. AOC 9KLR v3_123102 7 Operating Instructions AOC 9KLR Front Panel Buttons Shuttle Knob: Press this knob to open the OSD window or select a highlighted function. Rotate this knob to switch functions or adjust settings. Power Indicator: A green light indicates that the monitor is on. An orange light indicates that the monitor is in Off mode. Note: This monitor automatically turns on when it is plugged into an AC outlet. Power: Press this button to put the monitor into Off mode. The power indicator will turn orange. Press and hold this button again to restore the monitor to normal operation mode. On-screen Display (OSD): Press the Shuttle Knob to open the OSD window and adjust settings on your monitor. (See next page.) AOC 9KLR v3_123102 8 Operating Instructions AOC 9KLR Adjusting the OSD Settings 1. Press the Shuttle Knob to open the OSD window. 2. Rotate the Shuttle Knob until the desired function is highlighted. 3. Press the Shuttle Knob again to open the function’s window. 4. Rotate the Shuttle Knob to change the settings of the function. 5. To save and exit, select the exit function or leave the monitor alone for 10 seconds. If you want to adjust any other function, repeat steps 2-4. Note: When the OSD window is open, the input signal timing settings appear at the top. H: stands for horizontal frequency and V: stands for vertical frequency. AOC 9KLR v3_123102 9 Operating Instructions AOC 9KLR Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC1 and DDC2B. The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information. The DDC2B is a bidirectional data channel based on the I.C protocol. The host can request EDID information over the DDC2B. Windows INF Driver File Most computers will automatically configure your monitor to work with your computer. For optimal viewing of your monitor, download the AOC monitor driver. Follow these steps: 1. Go to 2. Click on SUPPORT to open the drivers web page. 3. Follow the directions on the web page to download and install the driver on your computer. Or go to to directly access the driver web page. AOC 9KLR 10 v3_123102 Technical Support (FAQ) AOC 9KLR Problem Possible Solution Power LED is not ON • Make sure the power cord is properly connected to a grounded poweroutlet and to the monitor. No Plug & Play • Confirm that your computer is Plug & Play compatible. • Confirm that your video card is Plug & Play compatible. • Inspect the video cable and make sure that none of the pins are bent. • Make sure the AOC monitor drivers are installed (AOC monitor drivers are available at: Picture is fuzzy • Adjust the Contrast and Brightness settings. Picture bounces or a wave pattern is present in the picture • Move electrical devices away from the monitor. They may be causing electrical interference. Power LED is ON (green or • Press a key on the keyboard or wiggle the mouse to re-activate theorange light is ON) but monitor. there is no video or picture. • Make sure the video cable is properly connected to the computer. • Inspect the video cable and make sure none of the pins are bent. • Make sure your computer is operating correctly by pressing the CAPSLOCK key and observing whether the CAPS LOCK light turns ON orOFF. Missing one of the primary colors (RED, GREEN, or BLUE) • Inspect the video cable and make sure that none of the pins are bent. • Make sure the video cable is properly connected to the computer. Screen image is not centered or sized properly • Adjust the Horizontal, Vertical or Zoom settings in the OSD window. Picture has color defects (white doesn’t look white) • Adjust the User Color setting in the OSD window. AOC 9KLR 11 v3_123102 Appendix AOC 9KLR Specifications CRT Size 19.0" (48.3 cm) 11.4” (29 mm) neck 0.21mm(H), 0.25mm(D) dot pitch 90 degree deflection Viewable image size 18.0” (45.7 cm) diagonal Preset Display area 13.6” (3...
Dieses Handbuch ist für folgende Modelle:Monitore - 9KLR (449.34 kb)