Using 2mm (5/64) allen wrench, remove orifice from end of nozzle extension (Figure 23). 3. Remove in-line filter from other end of nozzle extension. 4. Use small diameter wire or a small paper clip to free any foreign material clogging or restricting orifice (Figure 23). 5. Using a garden hose, remove additional debris by back flushing water through nozzle extension (Figure 24). Back flush between 30 to 60 seconds.Turn adjustable nozzle extension to stream spray and move nozzle from low to high

2. Check that high pressure hose is tightly connected to spray gun and pump. See “Preparing Pressure Washer for Use” for illustrations. 3. Make sure unit is in level position. 4. Connect garden hose to water inlet on pressure washer pump. Turn ON water. CAUTION! DO NOT run the pump without the water supply connected and turned on.You must follow this caution or the pump will be damaged. 5. Squeeze spray gun trigger until a steady stream of water occurs. 6. For models 01806 and 01936, place quick

Perform these tasks to prepare unit for operation: • Attach the handle to the main unit. • Add oil to the engine. • Add fuel to the fuel tank. • Connect the high pressure hose to the spray gun and the pump. • Connect the water supply to the pump. • Connect nozzle extension to spray gun. • Select and install desired nozzle (if applicable). Attach Handle to Unit This manual describes assembly and use of three models (01805, 01806 and 01936). Please see the appropriate section for the handle instru

4. Make sure black spray tip is installed. NOTE: Detergent cannot be applied with high pressure spray tips (White, Green,Yellow, or Red). Figure 10 — Spray Tips Black Low Pressure Use to apply detergent White 40° Green 25° Yellow 15° High Pressure Red 0° 12 Section 4: Operation 5. Make sure garden hose is connected to water inlet. Check that high pressure hose is connected to spray gun and pump; start engine. 6. Apply detergent to a dry surface, starting at lower portion of area to be washed and

Automatic Cool Down System — Cycles water through pump when water reaches 125°-155°F.Warm water will discharge from pump onto ground.This system prevents internal pump damage. Chemical Injection Siphon/Filter — Use to siphon detergent or other pressure washer chemicals into the low pressure stream. Choke Lever — Prepares a cold engine for starting. Fuel Tank — Fill tank with regular unleaded pressure washer. Always leave room for fuel expansion. Fuel Valve — Used to turn fuel on and off to engin

020224-1 (2700 PSI Pressure Washer) Manual No. 203763A Revision B (04/23/2007) EXPLODED VIEW AND PARTS LIST EXPLODED VIEW AND PARTS LIST - MAIN UNIT — 6 ■11 — 10 — 9 — 7 — B Item Part # Description Item Part # Description 1 198732GS ASSY, Base 16 196902GS KIT, Nozzle 2 M194567GS HANDLE 198841GS Nozzle, QC, Plastic, Soap 3 200170GS ASSY, Billboard w/Decals & Clips 195983WGS Nozzle, QC, Red 195964GS Clips, Tree 195983XGS Nozzle, QC, Yellow 4 196006GS HOSE 195983ZGS Nozzle, QC, White

STRATTON 3200 PSI / 220 BAR Illustrated Parts List BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC JEFFERSON, WISCONSIN, U.S.A. Model No. 020225-0 (3200 PSI Pressure Washer) Manual No. 203764A Revision C (11/07/2007) EXPLODED VIEW AND PARTS LIST EXPLODED VIEW AND PARTS LIST - MAIN UNIT °n0 o 0 — 11 —10 % — 9 ( — 17 Item Part # Description 1 M194424GS BASE 2 M196133GS HANDLE 3 30809GS GROMMET 4 B4805GS HOSE, 50’ 5 192134GS KIT, Engine Mounting Hardware 6 192132GS KIT, Pu

It is not included with the pressure washer. Contact the nearest authorized service center to purchase PumpSaver. To use PumpSaver, make sure the pressure washer is turned off and disconnected from supply water. Read and follow all instructions and warnings given on the PumpSaver container. CAUTION You must protect your unit from freezing temperatures. • • Failure to do so will permanently damage your pump and render your unit inoperable. Freeze damage is not covered under warranty. CAUTION Read