When the engine starts, open the choke completely. Trigger Safety Latch WARNING To reduce the risk of serious bodily injury, including fluid injection or splashing in the eyes or on the skin, always engage the trigger safety latch when you stop spraying even for a moment. In the engaged position, the trigger safety latch prevents the gun from being triggered accidentally by hand or if it is dropped or bumped. Be sure the latch is pushed fully down, or it will not prevent the gun from being trigg

4. Inspect all parts, and replace as necessary. 5. Thoroughly clean the packing cavities, and examine for debris or damage. 6. Lightly grease packing cavities, and replace packings in following order: ring head (45), V-packing (44), restop packing (47), intermediate ring (46). Install o-ring (42) in retainer groove and then install retainer ring (43) with low pressure seal (57). CAUTION Install the parts in the proper order and facing the proper direction. Improperly installed parts will cause a

The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale. GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR C

. After each use, wipe all surfaces of the pressure washer with a clean, damp cloth. . Perform the appropriate maintenance. See Maintenance Chart at right. Maintenance Observing regular maintenance intervals helps ensure that you get maximum performance and life from the pressure washer. There is a break-in period for the engine and pump. After you change the oil in these components following their respective break-in periods, the interval between required changes is longer. If the pressure wash

. If you use the Sandblaster Kit, see the Sandblaster Kit manual for detailed cleaning information. . See manual 308513 for chemical injector operation and service. 1. Check the oil level. NOTE: This pressure washer is equipped with a low-oil sensor that shuts the engine off if the oil level falls below a certain level. If the engine stops unexpectedly, check the oil and the fuel levels. Check the oil level each time you refuel. 2. Check the fuel level. WARNING FIRE HAZARD Do not refuel a hot en

G–Force Direct-Drive Pressure Washer 2525LD Model 246601, Series A & Series B 2300 psi (159 bar, 15.8 MPa) Maximum Operating Pressure 2500 psi (172 bar, 17.2 MPa) Maximum Working Pressure 2626LD Model 249065, Series A 2600 psi (179 bar, 17.9 MPa) Maximum Operating Pressure 2750 psi (191 bar, 19.0 MPa) Maximum Working Pressure ti6075a ti3224b 2525LD 2626LD GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 COPYRIGHT 2003 GRACO INC. Graco Inc. is registered to I.S. EN ISO 9001 Table of Contents S

Setup Connect to Water Supply Connect hose from water supply to the garden hose inlet on the pressure washer. • The supply hose should not be longer than 50 ft (15 m) in length. • Inside diameter of hose should measure at least a 3/4 in. (19 mm). ti5420ati5422a Up to 100 ft (30 m) of 3/8 in. high-pressure hose may be used. Longer hoses could affect pressure washer and chemical injector performance balance. Installing Spray Tip Install spray tip on wand. (Installing and Changing Spray Tips, page.

No. 1 2 3 4 5 7 8 9 10 11 12 13 15 16 17 18 Part No. Description Qty. 116299 ENGINE, gasoline, 6.5 HP Briggs and Stratton 1 244749 PUMP, water, 2700, complete 1 244767 KIT, frame, includes wheels, feet and tip grommets 1 244784 GUN 1 244783 HOSE, 4000 1 804511 WHEEL, pneumatic 2 805535 TIP, spray, red, 0° 1 805536 TIP, spray, yellow, 15° 1 805537 TIP, spray, green, 25° 1 805538 TIP, spray, white, 40° 1 244768 KIT, tip, 4-pack 1 805634 TIP, spray, chemical 1 804275 TUBING, chemical, 5/16 in. ID x

Be sure latch is pushed fully down or it will not prevent the gun from being triggered. • When using a sandblasting kit, refer the sandblaster kit instruction manual for detailed operating and cleaning information. 1. Check oil level of engine and pump. 2. Check fuel level. 3. Check oil level in pump. It should be half way up the sight glass, located on the front of the pump. Add pump oil as necessary. The system is equipped with a thermal overload to help prevent severe damage. 4. Turn on water

. Follow Pressure Relief Procedure on page 5 if the spray tip clogs and before you clean, check, or service this equipment. . Repair or replace worn or damaged parts immediately. . Check hoses, tubes, and couplings daily. Do not repair high-pressure couplings; you must replace the entire hose. Fluid hoses must have spring guards on both ends to prevent kinks and rupture. 2 308524 WARNING MOVING PARTS HAZARD Moving parts, such as the drive belt, can pinch or amputate fingers. . Keep clear of movi