Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
. Fill with lubricant following the instructions in Adding/ Checking Engine Lubricant earlier in this manual. . Before using the pressure washer, check to ensure that no lubricant is leaking from the engine. NOTE: Used lubricant should be disposed of at an approved disposal site. See your local oil retailer for more information. CHECKING SPARK PLUG See Figure 23. . Clean the area around the base of the spark plug before removing to keep dirt and debris out of the engine. Remove spark plug. . Clean off carbon deposits on the spark plug electrode using a plug cleaner or wire brush. Replace the plug if worn or reuse is questionable. (Recommended spark plug: Champion RC12YC). . Check electrode gap. The gap should be 0.7 - 0.8 mm in. Adjust the gap, if necessary, by carefully bending the ground electrode. . Check the condition of the spark plug gasket. . Reinstall spark plug. Start the spark plug in its threads by hand and finger-tighten. . Tighten with wrench to compress washer. If spark plug is new, use 1/2 turn to compress washer appropriate amount. If reusing old spark plug, use 1/8 to 1/4 turn for proper washer compression. NOTE: An improperly tightened spark plug will become very hot and could damage the engine. PUMP MAINTENANCE Routinely make a visual inspection of the pump. If you notice any leaking of lubricant around the pump seals, take the pressure washer to an authorized service center for repair. There are no user serviceable parts to the pressure washer pump. Any attempt to service or alter the pump may damage the pressure washer and void your product warranty. STORING THE PRESSURE WASHER See Figure 24. Store the pressure washer with the gas tank empty by either draining the tank or running the pressure washer until the gas runs out. Allow 30 minutes of “cool down” time before storing the machine. Store in a dry, covered area where the weather can’t damage it. It is important to store this product in a frost-free area. Always empty water from all hoses, the pump, and the detergent bucket before storing. NOTE: Use of a fuel stabilizer and pump saver will give you better performance and increase the life of the machine. Discharge Fuel: Drain the fuel tank completely. Stored gas can go stale in 30 days. Page 13 — English MAINTENANCE Engine Lubricant: Drain the lubricant and replace with fresh, clean lubricant. Spark Plug: . Disconnect spark plug wire and remove the spark plug. Pour about a teaspoon of clean, air-cooled, four-cycle lubricant through the spark plug hole into the combustion chamber. . Leaving the spark plug out, pull the starter cord two or three times to coat the inside of the cylinder wall. . Inspect the spark plug and clean or replace, as necessary. . Reinstall the spark plug, but leave the spark plug wire disconnected. Air Filter: . Clean the air filter. Recoil Starter Rope: . Extend the recoil starter rope to check its condition. If the rope is frayed, have it replaced immediately by an authorized service center. Hoses and Pump: Flush the injection hose with clean water for 1-2 minutes. Remove all hoses. Empty the pump by pulling on the recoil starter about 6 times. This should remove most of the liquid from the pump. For winterizing and long-term storage: • Disconnect the water connection, if necessary. • Start the pressure washer and allow it to run for a few seconds to eliminate any water remaining in the pump. • Coil the hoses and place in the hook-and loop strap on the unit’s handle. Do not allow the hose to become kinked. • Store the unit and accessories in an area that does not reach freezing temperatures. Do not store near furnace or other sources of heat that could dry out the pump seals. CAUTION: The use of a pump protector is recommended to prevent cold weather damage during storage over the winter months. PREPARING FOR USE AFTER STORAGE . Pull the recoil starter grip three or four times to clean lubricant from the combustion chamber. . Remove spark plug from the cylinder. Wipe lubricant from the spark plug and return it to the cylinder. . Reconnect the spark plug wire. . Refuel the machine as described earlier in the operator’s manual. PERIODIC MAINTENANCE SCHEDULE TABLE Maintenance Items Each Every Every Every Every Every use 8 hrs. 20 hrs. 50 hrs. 100 hrs. 300 hrs. Clean engine & check bolts & nuts X X Check engine oil X Change engine oil* X Clean spark plug X Clean air cleaner X X Replace air cleaner element X Clean & adjust spark plug & electrodes X Replace spark plug X Remove carbon from cylinder head** X Check & adjust valve clearance** X * Initial oil change should be performed after the first 20 hours of operation. Do not pour old oil down sewage drains, into garden soil, or into open streams. Your local zoning or environmental regulations will give you more detailed instruction on proper disposal. ** Have performed by your nearest service center Page 14 — English TROUBLESHOOTINGTROUBLESHOOTING PROBLEM CAUSE SOLUTION Engine fails to start No fuel in tank Spark p...