Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Disconnect the high pressure hose from the pressure washer and trigger gun. 4. Disconnect garden hose from pressure washer. 5. Remove excess water from the pump by tipping the unit on both sides to drain any remaining water from the water intake and outlet fittings. 6. Drain detergent applicator bottle and flush with clean water. 7. Wipe away any remaining water on all parts and fittings. 8. Engage the trigger gun safety lock. 9. Store the unit and accessories in a room above 32°F. Winterizing & Long Term Storage 1. Disconnect all water connections. 2. Turn the pressure washer on for a few seconds, until any remaining water in the pump exits. 3. Turn the unit off immediately. 4. Store the pressure washer, parts and accessories in an area with a temperature above 32°F. Motor Thermostat Important: This pressure washer is equipped with a motor thermostat. The motor will stop if it is overheating. Wait 10-20 minutes before starting the unit again. If it stops again, please call FANTOM customer service at 1-800- 798- 7398. Ground Fault Circuit Interrupter (GFCI) This unit is equipped with a Ground Fault Circuit Interrupter ( GFCI) built into the plug. This device provides additional protection from the risk of electrical shock. When connecting the GFCI to the electrical outlet, the indicator should appear red. If the indicator is not red, depress the RESET button on the GFCI until the indicator appears red. Cleaning Tips Wood Decks: Rinse deck and surrounding area with fresh water. If using detergent, fill the detergent applicator bottle and apply to the area being cleaned. For optimal results, reduce your work area to small sections and clean each section one at a time. Allow the detergent to rest on the surface for a few minutes and then rinse at high pressure. Do not let the detergent dry on the deck. Always clean from left to right and top to bottom for best results. Rinse at high pressure using the fan jet keeping the tip of the spray nozzle 8- 12 inches from the surface. Caution: For soft woods, increase the distance from the cleaning surface. Cars, Boats, & Motorcycles: Wet down area to be cleaned before applying detergent with clean water. Fill the detergent applicator bottle and apply to the area being cleaned. To achieve best results, clean one side at a time. Allow the detergent to rest on the surface for a few minutes but do not let it dry. Rinse at high pressure using the fan jet in a sweeping motion keeping the tip of the spray nozzle at least 8-10 inches away from the surface. Maintain a further distance when using a direct spray. Wipe surface for a polished finish. 8 GETTING TO KNOW YOUR PRESSURE WASHER789101211131415161. Pressure Washer2. Water Intake3. High Pressure Output4. On/Off Switch5. Trolley6. Trolley Handle7. High Pressure Hose8. Brush 9. Trigger Gun10. Safety Lock11. Trigger 12. High Pressure Hose Connector13. High Pressure Lance14. Adjustable Fan Jet Lance15. Detergent Applicator Bottle16. Garden Hose Coupling17. Handle Bracket18. Top Brace19. Legs (x2) 20. Support Bracket ( x2) 21. Wheel ( x2) 22. Front Support23. Trolley Screws ( x11) (not shown) Technical SpecificationsVoltage: 120V., 60Hz. Power: 12.5 Amps. Pressure: 1450 psi. (max) Flow Rate: 1.45 gpmIllustrations may differ from actual product.3 OPERATING INSTRUCTIONS Unpacking Your Pressure Washer After you open the package, check to make sure that all the parts are in the box as pre parts that illustrated on page 3 of this guide. Due to transport and packing restraints, some accessories may be supplied unassembled; in this case follow the assembly instructions in this manual. If you have any questions, call FANTOM customer service at 1-800-798-7398. Keep all small and potentially harmful parts of the package (plastic bags, foamed polystyrene, nails, etc.) out of the reach of children. 3. Place the pressure washer between the two support brackets and secure with the two ( 2) screws provided. (Fig. 3) 4 7 This high pressure washer is suitable for non-professional use. The working temperature must range between 40°F and 120 °F. The machine is supplied with a trigger gun, equipped with a trigger handle to offer a comfortable working position. The high pressure washer is suitable for washing with cold water only. The water that you use for the pressure washer must not be dirty, sandy or contain any corrosive chemical products. The pressure washer may be used to wash shutters, doors, tiles, cars, decks, campers, etc., where high water pressure is necessary to remove dirt. With the detergent applicator bottle, the pressure washer can be used to apply a thick coating of aerated detergent to the areas being cleaned . When using the pressure washer we recommend the use of personal safety items to reduce the risk of accidental injury. Suitable Use of Your Pressure Washer• Place the pressure washer in a safe area and on a horizontal surface. • When using the pressure washer, hold the trigger gun firmly with one hand on the handle and the ...