Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Brush17. Hose Connector18. Garden Hose Coupling19. Water Intake FilterTechnical SpecificationsVoltage: 120V., 60Hz. Power: 13 AmpsPressure: 1900 psi. (max) Maintenance & Cleaning Lubrication: The pressure washer is supplied with a closed lubrication system, so no addition of oil is needed. Checking the Water Intake Filter: The water intake filter is located inside the water intake connector. (Fig. 18) Remove periodically and inspect for any deposits that might accumulate there.Fig. 18Cleaning the Nozzles: If you notice that the output pressure fluctuates, you may have to clean the nozzles. Turn the unit "Off". Unplug from electric outlet and disconnect the water supply. Remove the lance, trigger gun and hose from unit. Take the small metal pin provided and insert into the nozzle end to remove any obstructions. (Fig. 19) Fig. 19Hose Connector Water IntakeThis will occur more frequently if your water supply is very hard.OPERATING INSTRUCTIONSStoring Your Pressure WasherWhen you have finished using your pressure washer, follow these steps for safe storage:1. Turn the pressure washer to the "Off" position. 2. Turn off the water supply. 3. Before disconnecting the high pressure hose connection, point the trigger gun in a safe direction away from you and discharge the high pressure water. Disconnect the high pressure hose from the pressure washer and trigger gun. 4. Disconnect the garden hose from pressure washer. 5. Remove excess water from the pump by tipping the unit on both sides to drain any remaining water from the water intake and outlet fittings. 6. Wipe away any remaining water on all parts and fittings. 7. Engage the trigger gun safety lock. 8. Store the unit accessories in a room above 32°F. Winterizing & Long Term Storage1. Disconnect all water connections. 2. Turn the pressure washer on for a few seconds, until any remaining water in the pump exits. 3. Turn the unit off immediately. 4. Store the pressure washer, parts and accessories in an area with a temperature above 32°F.Motor ThermostatImportant: This pressure washer is equipped with a motor thermostat. The motor will stop if it is overheating. Wait 10- 20 minutes before starting the unit again. If it stops again, please call customer service at 1 (800) 798- 7398. Ground Fault Circuit Interrupter (GFCI)This unit is equipped with a Ground Fault Circuit Interrupter ( GFCI) built into the plug. This device provides additional protection from the risk of electrical shock. When connecting the GFCI to the electrical outlet, the indicator should appear red. If the indicator is not red, depress the RESET button on the GFCI until the indicator appears red. Cleaning TipsWood Decks: Rinse deck and surrounding area with fresh water. If using detergent, fill the detergent applicator bottle and apply to the area being cleaned. For optimal results, reduce your work area to small sections and clean each section one at a time. Allow the detergent to rest on the surface for a few minutes and then rinse at high pressure. Do not let the detergent dry on the deck. Always clean from left to right and top to bottom for best results. Rinse at high pressure using the fan jet keeping the tip of the spray nozzle 8-12 inches from the surface. Caution: For soft woods, increase the distance from the cleaning surface. Cars, Boats, & Motorcycles: Wet down area to be cleaned before applying detergent with clean water. Fill the detergent applicator bottle and apply to the area being cleaned. To achieve best results, clean one side at a time. Allow the detergent to rest on the surface for a few minutes but do not let it dry. Rinse at high pressure using the fan jet in a sweeping motion keeping the tip of the spray nozzle at least 8-10 inches away from the surface. distance when using a direct spray. Wipe surface a polished finish.8 4 7 CAUTIONTriggerLockWhen you wish to stop using the pressure washer temporarily, make sure that the trigger lock has been engaged to avoid any accidental operation. (Fig. 12) Fig. 12Using Brush With the Trigger GunThe brush is used with the trigger gun. Push the brush onto the trigger gun nozzle and turn clockwise to lock as you would for the lance. (Fig. 15) The brush may be used for washing cars, boats, windows and other similar items. The brush operates at open orifice pressure so it will not direct a stream of water. Fig. 15OPERATING INSTRUCTIONSFig. 16Using the Adjustable LanceThe angle of the water on the adjustable lance may be adjusted between 0° and 60° by turning the nozzle adjuster counter-clockwise for a wider angle or clockwise for a narrower angle. (Fig. 13 & Fig. 14) Always make sure that the "On/Off' switch is in the "Off" position before changing the angle of the water jet. It is also recommended that the trigger gun safety lock be engaged as well. The adjustable lance allows you to use any variety of spray pattern from a full fan spray to a direct stream spray. When using the pressure washer to clean wood decks, siding, vehicles, etc...