Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Installation Instructions Tools Required for Installation: Flat Screwdriver Hammer/Mallet Adjustable Wrench 1. Set plastic spacer (included in parts pack) on workbench (Figure 1). Figure 1 2. Place “star shaped” retaining ring on the spacer (tangs pointing down) (Figure 2). Figure 2 3. Tap the retaining ring onto the axle (Figure 3 & 4). Figure 4 4. Put both wheels on axle, solid sides together (Figure 5). Figure 5 Solid Sides 5. Attach opposite ring in the same manner (Figure 6). Figure 6 Figure 7 7. Snap wheel covers on the wheel. 8. Attach foot to front of pressure wash-er body (Figure 7). 9. Hook up chemical suction hose to the tip on the bottom of the handle (Figure 8). Figure 8 10. Attach black handle with enclosed screws and washers (Figure 9). Figure 9 Figure 3 6. Slide wheels out and snap axle into place on the underside of body (Figure 7). © 2003 Campbell Hausfeld/For parts, product & service information UL IN457001AV 2/03 Approved visit Assembly Instructions and Parts List PW167612AV Garden Hose Connection GARDEN HOSE CONNECTION INSTRUCTIONS 1. Attach nipple adapter to inlet fitting on the unit (this may already be attached to the pump). 2. Attach quick connect fitting to garden hose. 3. Pull side “A” of quick connect fitting toward garden hose and push onto nipple adapter. 4. Push side “A” of quick connect fitting towards nipple adapter and release. "A" Quick Connect Fitting Garden Hose Nipple Adapter Figure 10 - Garden Hose Connection Power Cord 1. Plug the power cord into a grounded 120V outlet and press the reset button as shown in Figure 11. 2. THIS MUST BE DONE EACH TIME THE UNIT IS PLUGGED IN AN OUTLET. Reset ! IMPORTANT ! This pressure washer is equipped with a microswitch sensitive to water flow. This Instant Start/Stop switch (ISS) senses water flow in the pump. When the trigger is released, water stops flowing through the pump. The ISS then automatically turns the motor off to protect pump from overheating. OPERATION 1. Pull trigger on gun. 2. Turn the “ ON/OFF” switch to “ ON” . 3. Release trigger. The pressure washer motor will stop running. 4. To spray again, pull trigger and motor and pump will restart. Note: Occasionally the motor may run for a short time to bring fresh, cool water into the pump even if trigger is released. This is part of normal operation and will not damage the unit. ! CAUTION Always turn the “ON/OFF” switch to “OFF” then trigger gun to release hose pressure before unplugging power cord. ! CAUTION Risk of equipment dam age. Always make sure the “ON/OFF” switch on the unit is “OFF” and unit is unplugged prior to storage. Risk of Injection. ! WARNING Unit will start spraying when trigger is squeezed if on/off switch is in “ON” position. Always point gun in safe direction. Call 1-800-330-0712 for Technical Service Figure 11 - Grounded plug/reset button 2 Assembly Instructions and Parts List PW167612AV System Connection 1. Insert lance into the gun and turn clockwise to positive stop as shown in Figure 12. Figure 12 - Gun/Lance Connection 2. Ensure that the power switch is in the “ OFF” position. 3. Attach the high pressure hose and gun assembly to the unit. 4. Connect garden hose as explained under Garden Hose Connection Instructions. 5. Plug the power cord into a grounded 120V outlet, that is on a dedicated circuit. 6. Turn water on. 7. Depress and hold the trigger on the gun for one minute to release pressure and remove any air trapped in the system. 8. Turn the “ ON/OFF” switch to the “ ON” position. NOTE: REFER TO PRODUCT MANUAL FOR OPERATING INSTRUCTIONS 13 mm Outlet Electrical Cord with GFCI High Pressure Hose Gun Garden Hose Handle/Detergent Tank Figure 13 - Connection Call-Outs 3 Assembly Instructions and Parts List PW167612AV For Replacement Parts, Call 1-800-330-0712 Please provide following information: -Model number -Serial number (if any) -Part description and number as shown in parts list Address parts correspondence to: The Campbell Group / Parts Dept. 100 Production Drive Harrison, OH 45030 U.S.A. REPAIR MANUAL FOR PRESSURE WASHERS 1 3 5 4 6 7 2 8 1310, 11, & 12 14 NOW AVAILABLE! • Step-by-step instructions lead you through the removal, inspection and replacement of key parts • Jam-packed with pictures, line art and exploded views To order call 1-800-330-0712 Replacement Parts List Ref. Part No. Description Number Qty. 1 Adjustable Lance PM257000SV 1 2 Turbo Lance PM257100SV 1 3 Hose PM243600AV 1 4 Gun PM037201AV 1 5 Nipple Adapter PM022100AV 1 6 Quick Connect Fitting PM020600SV 1 7 Tip Cleaner PM008500AV 1 8 Detergent Tank PM059000SV 1 9 Hardware Pack (Upper Handle/Wheels/Front Foot) PM062200SV 1 10 Axle PM062400SV 1 11 Wheels PM059100SV 2 12 Wheel Covers PM059200SV 2 13 Front Foot PM059400AV 1 14 Cap, Detergent Tank PM060000SV 1 4 Instructions de Montage et Liste de Pieces de Rechange PW167612AV S’il vous plait lire et conserver ces instructions. Lire attentivement avant de monter,...