Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Avoid spraying windows with a narrow high impact stream or turbo nozzle. Doing so may break the window. The surest way to avoid damaging surfaces is to follow these steps: 1. Before triggering the gun, adjust the nozzle to a wide fan pattern. 2. Place the nozzle approximately 4-5 feet away from the cleaning surface. Then hold the nozzle at a 45° angle to the cleaning surface. Trigger the gun. 3. Vary the fan pattern spray angle and the distance to the cleaning surface until optimum cleaning efficiency is achieved without damaging the surface. Nozzle cleaning Instruction A clogged or partially clogged nozzle can cause a significant reduction of water coming out of the nozzle and cause the unit to pulsate while spraying. To clean out the nozzle: • Turn off unit. • Turn off water supply. Relieve any pressure trapped in the hose by squeezing trigger 2-3 times. 6 7 • Separate lance from gun. • Rotate nozzle to the narrow stream setting. This opens up the fan blades. • Using the included tip cleaner, or an un-folded paper clip, insert wire into the nozzle hole and move back and forth until debris is dislodged (refer to Figure 7). • Remove additional debris by backflushing water through the nozzle. To do this, remove the lance from the gun, place end of a garden hose (with water running) to tip of nozzle pushing water and debris out the back opening of the lance. Detergents The use of detergents can dramatically reduce cleaning time and assist in the removal of difficult stains. Some detergents have been customized for pressure washer use on specific cleaning tasks. These detergents are approximately as thick as water. The use of thicker detergents, such as dish soap, will clog the chemical injection system and prevent the application of the detergent. The cleaning power of detergents comes from applying them to a surface and giving the chemicals time to break down the dirt and grime. Detergents work best when applied at low pressure. The combination of chemical action and high pressure rinsing is very effective. On vertical surfaces, apply the detergent starting at the bottom and work your way upward. This will prevent the detergent from sliding down and causing streaks. High pressure rinsing should also progress from the bottom to top. On particularly tough stains, it may be necessary to use a brush in combination with detergents and high pressure rinsing. Operating Instructions and Parts List PW1350 Nozzle Cleaning Instructions (Continued) Figure 8 High Pressure Hose Gun Lance Pressure Washer GFCI Plug ON/OFF Switch Water Outlet Water Inlet Swivel Adapter Garden Hose Trigger Lock Nozzle Tip Cleaner Figure 7 Operating Instructions and Parts List PW1350 Operation 1. The lance is affected by pressure during operation; therefore hold it firmly with both hands and point the nozzle toward the ground. 2. Activate by pulling the trigger of the gun/spray handle. 3. Adjust the distance to the cleaning surface, which will also adjust your pressure of the nozzle. 4. Spray pattern shape and intensity can be changed by twisting the spray adjuster at the end of the lance. Keep hands clear of the front of the lance to prevent injury. See Figure 9. END OF OPERATION 1. Press the ON/OFF switch to “OFF” on the pressure washer. 2. Disconnect the plug from the power source. 3. Shut off the water supply. 4. Activate the spray handle to relieve the machine of pressure. 5. Lock the trigger into the “OFF” position. 6. Remove high pressure hose from unit after each use. TIP: It is best to remove all hoses when storing unit for long periods of time. Figure 9 - Spray Adjust Notes 8 9 Ref. No. Description Part Number Qty. 1 Swivel Adapter PM350100SV 1 2 Filter PM350101SV 1 3 Hose PM350102SV 1 4 U-Pin PM350107SV 1 5 Gun PM350103SV 1 6 O-ring PM232200SV 1 7 Adjustable Fan Lance PM350104SV 1 8 Tip Cleaner PM008500AV 9 Switch N/A 1 10 Pump Outlet N/A 1 11 Pump Inlet N/A 1 12 Detergent Bottle (optional) PM350105SV 1 Operating Instructions and Parts List PW1350 For Replacement Parts or Technical Assistance, Call 1-800-330-0712 Please provide following information: - Model number - Serial number (if any) - Part description and number as shown in parts list Address parts correspondence to: Campbell Hausfeld Attn: Customer Service 100 Production Drive Harrison, OH 45030 U.S.A. 1 2 11 10 9 8 7 6 5 4 3 12 Operating Instructions and Parts List PW1350 Limited Warranty 1. DURATION: From the date of purchase by the original purchaser as follows: One Year. 2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, OH 45030, Telephone: (800) 330-0712 3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld pressure washer. 4. WHAT PRODUCTS ARE COVERED UNDER THIS WARRANTY: Any Campbell Hausfeld Pressure Washer supplied or manufactured by the Warrantor. 5. WHAT IS COVERED U...