Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
You can vary the impact force by controlling the spray tip angle to the cleaning surface and the distance from the cleaning surface and by changing the spray tip. NEVER use a narrow high impact stream on a surface that is susceptible to damage. Avoid spraying windows with a narrow high impact stream. Doing so may break the window. The most sure way to avoid damaging surfaces is to follow these steps: 1. Before triggering the gun, make sure the quick connect tip you are using is appropriate for the application. 2. Place the spray tip approximately 4-5 feet (1,22-1,52 m) away from the cleaning surface. Then hold the lance and spray tip at a 45 degree angle to the cleaning surface. Trigger the gun. 3. Vary the fan pattern spray angle and the distance to the cleaning surface until optimum cleaning efficiency is achieved without damaging the surface. The color of the tip shows what spray angle it is: Red – 0° – Maximum Duty* Yellow – 15° – Heavy Duty Green – 25° – General Duty* White – 40° – Light Duty* Black – 65° – Low Pressure Detergent * = Not Included 4. Detergent Application NOTE: Use only detergents formulated for pressure washers.Test detergent in an inconspicuous area before use. DETERGENTS The use of detergents can dramatically reduce cleaning time and assist in the removal of difficult stains. Many detergents are customized for pressure washer use on specific cleaning tasks. Pressure washer detergents are as thick as water. Using thicker detergents – like dish soap – will clog the chemical injection system and prevent the application of the detergent. Once applied to a cleaning surface, detergents take time to break down dirt and grime. Detergents work best when applied at low pressure. You can effectively clean surfaces by combining the chemical action of detergents with high pressure rinses. On vertical surfaces, apply the detergent starting at the bottom and work your way upward. This method prevents the detergent from sliding down and causing streaks. Begin high pressure rinsing at the bottom and work your way upward. On particularly tough stains, use a brush in combination with detergents and high pressure rinsing. 1. Follow manufacturer’s label directions for mixing correct concentrations of soap/detergents. The soap detergent to water ratio through the pump is approximately 12% (1 to 8). 2. Pour detergent into the detergent tank. The tank capacity is 1.5 gallons. 3. Install 65. (Black) Low Pressure Detergent Tip in the quick connect fitting on the end of the lance. NEVER replace quick connect tip when gun ! WARNING is triggered. Always engage trigger lock on gun before removing or installing quick connect tips. GENERAL CLEANING TIPS 1. Apply the detergent so that it thoroughly covers the cleaning surface. Apply the detergent from bottom to top to prevent the detergent from sliding down and streaking. Wait a couple of minutes for the detergent to break down the dirt and grime. Use a brush to lightly scrub heavily soiled areas. Never allow the detergent to dry on the cleaning surface. 2. Replace black 65. quick connect tip with the yellow 15. tip and complete final rinse. NEVER replace quick connect tip when gun ! WARNING is triggered. Always engage trigger lock on gun before removing or installing quick connect tips. 3. NOTE: After using detergents, flush the suction system by rinsing out tank with clean water and running unit with black 65. tip flushing clean water from tank through the pump. 8 Pressure Washer Operation (Continued) 5. Cleaning Power The easiest way to regulate the cleaning power of your pressure washer is by changing the distance from the surface you are cleaning. Begin spraying while standing several feet from the surface. Slowly move closer to the object you are cleaning until you find the most effective cleaning technique. 6. Final Rinse The final rinse should start at the bottom and work upward. Make sure that you thoroughly rinse the surface and that you remove all detergent. 7. Pressure Relief Procedure To reduce the risk of bodily injury or property damage, always follow this procedure whenever spraying is stopped, when work is completed, and before checking or repairing any part of the system. 1. Engage the trigger safety latch. 2. Turn the unit off. 3. Shut off the water supply. 4. Disengage the trigger safety latch and trigger the gun to relieve pressure. 5. Re-engage the trigger safety latch. 6. When checking or repairing unit, remove the ignition cable from the spark plug. 7. Before overnight storage, long term storage, or transporting unit, disconnect the water supply and turn off the fuel supply valve. 8. Shutdown 1. Be sure all detergent is flushed from system. 2. Turn the engine OFF. 3 Turn the water supply OFF. 4. After the engine and water supply are turned off, trigger the gun to depressurize the system. NEVER turn the water supply off before NOTICE turning the engine/motor off. Serious damage could occur to the pump and/or engine/motor. NEVER...